Tabla de contenido
Idiomas disponibles
Idiomas disponibles
English
Cleaning
Note
After use, always thoroughly clean
the mower.
Park the mower on firm and level
ground.
Actuate the parking brake.
Cleaning the cutter deck
!
Danger
Injury hazard due to sharp cutting
blades
Wear safety gloves.
Caution when cleaning the cutters.
Caution
Engine damage
The mower must not be tilted to an
angle greater than 30°. This might
cause fuel to run into the combusti
on chamber and could lead to engi
ne damage.
Raise the cutter deck fully.
Clean the cutting compartment
with a scrubbing brush, hand
brush or cloth.
Maintenance
Observe the servicing instructions in
the engine manual.
At the end of the season have the
mower inspected and serviced by a
specialist workshop.
Caution
Engine oil is hazardous to the envi
ronment
After changing the oil, take the
waste oil to a waste oil collecting
point or to a waste disposal compa
ny.
Batteries are an environmental ha
zard
Do not throw used batteries away
with domestic waste. Hand over
used batteries to your dealer or to a
waste management company. Re
move the battery before scrapping
the mower.
Using jump leads
!
Danger
Never bridge a defective or frozen
battery with jump leads. Ensure
that the machines and the jump
lead clips do not touch that the igni
tions are switched off.
14
Connect the red jump lead to the
positive terminal (+) of the flat
battery and the donor battery.
Connect the black jump lead first
to the negative terminal (–) of the
donor battery. Connect the other
clip to the frame of the engine
block of the vehicle with the flat
battery (as far away from the bat-
tery as possible).
Note
If the donor battery is installed in a
vehicle, this vehicle must not be star-
ted during the jump starting process.
Start the vehicle with the flat bat-
tery and actuate the parking bra-
ke.
Disconnect the jump leads in re-
verse sequence.
Tyre pressure
-
-
Caution
Never exceed the maximum per
mitted tyre pressure (see tyre wall).
When pumping up the tyres, do not
stand in front of or over the tyre.
The recommended operating tyre
pressure is:
front:
rear:
Excessive tyre pressure reduces the
service life of the tyres. Always
check the tyre pressure before dri-
ving.
After 5 operating hours
-
First engine oil change.
See engine manual for subse-
quent intervals.
After 10 operating hours
-
Lubricate all rotating and bearing
points (operating lever, height
-
adjustment of the cutter deck,
clutch/brake pedal, etc.) with se-
veral drops of light oil.
Clean battery terminals.
Every 25 operating hours
-
Lubricate all blade shafts, tensio-
ning pulleys and tensioning pul-
ley holders via the grease nipples
using grease type 251H EP. Ar-
range for this work to be carried
out by a specialist workshop.
Apply multipurpose grease to
the teeth on the steering gear.
-
Operating Manual for Ride-on Lawn Tractor
Every 50 operating hours
If required
Charge the battery
If you are not using the mower for a
prolonged period, removal of the
battery from the mower and char-
ging prior to storage is recommen-
ded, as well as every 2 months
during storage, and before starting
up the mower again.
Follow the instructions in the opera-
ting manual for your battery charger.
-
Replacing fuses
Once a season
1.0 bar
0.7 bar
Shutting down the unit
Material damage to the mower
Only store the mower once the en
gine has cooled in a clean and dry
room or area. During prolonged
storage, e.g. in winter, ensure that
the mower is protected against
rust.
Lubricate the steering linkage
with a few drops of light oil.
Lubricate wheel bearings and ax-
les of the front wheels via the
grease nipples (if fitted) using a
multi-purpose grease.
Dirt and grass remnants must be
removed from the drive gear by a
specialist workshop.
Note
Replace defective fuses only with
ones of an equal rating.
Apply multipurpose grease to
the teeth on the steering gear.
Lubricate the steering linkage
with a few drops of light oil.
Lubricate all rotating and bearing
points (operating lever, height
adjustment of the cutter deck,
clutch/brake pedal, etc.) with se-
veral drops of light oil.
Clean the spark plug and check
the gap between the electrodes
or replace the plug. See engine
handbook.
Have a repair shop lubricate
the wheel axles with special
grease (water-repellent).
The cutting blade must be shar-
pened or replaced by a specialist
workshop.
Caution
-
Capítulos
Tabla de contenido
