PLASTITALIA I Plast 105 Manual Del Usuario página 29

Code / Fusion report
ERROR 34.1!
(CURRENT_SHC_ERROR)
report sentence: "I2SCHE"
ERROR 34.2 !
(OUT_SHC_CURR_ERROR)
report sentence: "I1SCHE"
ERROR 36 !
(LOAD_MEASURE_ERROR3)
report sentence: " LoadE3"
ERROR 38 !
(LOAD_SHC_ERROR)
report sentence: "LoadSE"
ERROR 39.0 !
(CONTROL_VOLTAGE_ERROR)
report sentence: "VCtrEr"
ERROR 39.1 !
(OUT_VOLTAGE_ERROR)
report sentence: "VoutEr"
ERROR 41 !
(GENERAL_ERROR)
report sentence: "GenErr"
ERROR 42 !
(SERVO_ERROR)
report sentence: "SrvErr"
ERROR 43 !
(SYNC_ERROR)
report sentence: "SynkEr"
ERROR 44 !
(HW_SERVO_ERROR_FCTRL)
report sentence: "HFCEr"
ERROR 45 !
(SW_ERROR)
report sentence: "SwErr"
ERROR 50 !
(USER_STOP_ERROR)
report sentence: "UsrStp"
ERROR 70 !
(MEMORY_WRITING)
report sentence: "MemErr"
ERROR 80 !
WELD_AUTHORIZATION
19) Information on generators
I Plast 105 / 60 / 30 is equipped with internal circuits capable of accepting a variables input voltage and input frequency. Often
generators provide an electric current with characteristics not related with those of the network. This ECU:
•
allows greater tolerance of voltage and frequency to input current;
•
displays the tension and frequency to input current.
It also has two electronic systems capable of guaranteeing a:
•
start-up of progressive current demand, limiting the overhead of the generator;
• a progressive decrease of current request to the motor generator during the final phase of fusion. This is to avoid
the generation of currents which can elude the input filters and damage machine.
Cause
Before the fusion:
- current output request higher than possible.
E.g.: electronic limitation for safety reasons
During the fusion:
- current output request higher than possible.
A difference between coupling resistive parameters and
those indicated in the barcode have been found. The
fitting may have manufacturing defects.
Short circuit during fusion process
Output voltage not stable
Output voltage out of limits (too high or too low)
General error due to unexpected conditions.
The servo controller assisting the welding is defective.
Generic error.
Constantly occurrence of this error characterizes
calibration problems or electromechanical device
problems (shock or lack of any electrical contact between
parts).
Power controller defected.
Code error reception, bad working (communication) or
software error
The user has activated the red STOP button during the
welding cycle.
Full Memory or DMS failure (Data Memory System).
Welder must be authorized
Pag. 29
Solution
Check fitting's request of current is within control
unit limits.
Check fitting for short circuit.
Replace the fitting.
Check fitting for short circuit.
In case of manual fusion data input: check
fitting's request of current is within control unit
limits.
Replace the fitting and repeat welding procedure.
It is recommended to control nature and matches
of the product that you want to use. Replace the
fitting. In case of emergency try to shift from the
automatic data input to the manual data fusion
input.
Change fitting. Be sure to follow fitting's
manufacturer indications for a good joint's
preparation
Check power generator: refer to chapter 18 for
power generator specification.
Change energy supply. Connect the control unit
to a stable source.
Check power generator: refer to chapter 18 for
power generator specification.
Change energy supply. Connect the control unit
to a stable source.
If it happens 3 times in succession contact
technical support at no. +39 0941536311
Generic error. Shut off the device and then
restart, if the problem will stand please contact
technical support at no. +39 0941536311
Hardware error . A defect in the hardware has
been recognized. Please contact technical
support at no. +39 0941536311
Hardware error . A defect in the hardware has
been recognized. Please contact technical
support at no. +39 0941536311
No solution. Shut off the device and then restart,
in case the message is displayed again please
contact technical support at no. +39 0941536311
Read welding instruction of the fitting's
manufacturer before restart another welding
cycle.
Contact technical support at no. +39 0941536311
Use welder's badge when control unit will require
it