Rice Burger Grill Cleaning Procedure - Prince Castle 411-SDFM85CE Serie Manual Del Usuario

Rice Burger Grill Cleaning Procedure

This procedure covers the recommended daily
cleaning of the Prince Castle 411 Rice Burger Grill.
Procedure Frequency
Daily, possibly less frequently depending upon the soil
load.
Supplies
®
• McD Hi-Temp Grill Cleaner
®
• McD All Purpose Super Concentrate
®
• McD Sanitizer
®
• McD NO-SCRATCH™ Pads
• Metal Container Plate
• Prince Castle No. 257 Cleaning Tool Set
• Heat Resistant Gloves
• Meshed Grill Cloths (6 – 8)
• Bucket or other reservoir filled with lukewarm water
Procedure
1. Remove left over rice burgers, bun tray, and
Teflon sheet. Remove any other components
remaining on the placing table.
NOTE: Follow standard food carryover procedures.
2. Clean the grill in a well-ventilated area.
3. Start the exhaust fan above the Clamshell Grill.
4. Heat the grill to the cleaning temperature
(480°F/163°C).
NOTE: The Rice Burger Grill must be cleaned at
operating temperature.
5. Turn the Rice Burger Grill power switch to the
OFF position and disconnect the power plug.
WARNING: There is the possibility of electric
shock if cleaning is done without disconnecting
the power plug.
6. Put on the heat resistant gloves.
7. Open the grill and mount the red latch to its
mating stud on the handle.
8. Wipe top of the upper platen with a sanitized
towel.
9. Apply the McD ® NO-SCRATCH™ Pad to the
holder located within the Prince Castle No. 257
Cleaning Tool Kit.
411-561revB
NOTE: Use only the McD
not use the green abrasive cleaning pad. Do not
scrape or otherwise scratch the heating platens. The
use of metal scrapers, abrasive pads, or wire brushes
will permanently damage the surface of the heating
platens.
10. Pour the entire packet of McD
Cleaner into the metal container plate.
11. Use the McD ® NO-SCRATCH™ Pad to apply
McD ® Hi-Temp Grill Cleaner onto the surface of
the heating platens and along the edges. Dip the
flat edge of the McD
the metal container plate and saturate with McD
Hi-Temp Grill Cleaner. Allow the excess to drain
into the metal container plate. Do not scrub
while applying the McD
Cleaner. If the surface of the upper heating platen
is clean, no cleaning will be necessary. Allow at
least a three minute contact time between the
McD ® Hi-Temp Grill Cleaner and the surfaces.
NOTE: Ensure the McD
applied by the McD ® NO-SCRATCH™ Pad. Do not
apply the McD ® Hi-Temp Grill Cleaner directly onto the
surface of the heating platens. Do not brush or wash
the platens before the McD
applied.
12. Lightly scrub surfaces using the McD
NO-SCRATCH™ Pad until clean. Apply more
McD ® Hi-Temp Grill Cleaner as needed.
13. Apply the McD ® Hi-Temp Grill Cleaner onto the
bun fence on both sides of the heating platen.
Make sure to apply to the blocks at the four top
corners of the upper heating platen. Dip the flat
edge of the McD ®
metal container plate and saturate with the McD
Hi-Temp Grill Cleaner. Allow the excess to drain
into the metal container plate. Do not scrub
while applying the McD
Cleaner. Allow at least a three minute contact
time between the McD
and the surfaces.
14. Lightly scrub all surfaces using the McD
NO-SCRATCH™ Pad until all carbon deposits
have been removed. Apply additional McD
Hi-Temp Grill Cleaner as needed.
11
® NO-SCRATCH™ Pad. Do
® Hi-Temp Grill
® NO-SCRATCH™ Pad into
® Hi-Temp Grill
Hi-Temp Grill Cleaner is
®
® Hi-Temp Grill Cleaner is
®
NO-SCRATCH™ Pad into the
® Hi-Temp Grill
® Hi-Temp Grill Cleaner
®
®
Printed in USA 4/06 © 2006
®
®