Appliance Description - BERTO'S PLUS 600 Serie Manual De Instrucciones

ATTENTION!
The figures mentioned in the chapters are shown on the initial pages of this manual.

APPLIANCE DESCRIPTION

Sturdy stainless steel structure with 4 feet that can be
adjusted in height. External coat made of AISI 304 or AISI
430 steel. The special steel plate has a smooth or ribbed
surface, equipped with side and back steel splashguards
or an oil collecting groove along the perimeter of the
unit. The plate is heated by tubular steel burners resistant
to thermal or mechanical stresses. The pilot burner is
equipped with a safety device and a thermocouple. The
temperature can be regulated by means of proper taps
equipped with safety devices.
The double module modes are equipped with separate
cooking areas and independent temperature controls.
PREPARATION
Location
The appliance should be installed in a well ventilated room
and, if possible, under a range hood. The appliance can be
installed on its own or alongside other equipment. Always
keep a minimum distance of 150 mm on the sides and 150
mm on the back from the wall.
The walls near the appliance (walls, decorations, kitchen
cabinets, decorative finishes, etc.) must be made of non-
flammable material.
If the unit is to be positioned on a table or a shelf, make sure
their materials are non-flammable. Before connecting the
appliance to the gas supply, check the data plate to make
sure that the appliance is fitted for the type of available
gas. If not, see the paragraph "Running appliances on
other types of gas".
Law provisions, technical regulations and directives
Before installing, check that the following provisions are
met:
- UNI CIG 8723 regulation
- building regulations and local fire prevention measures;
- accident prevention regulations in force;
- local Gas Board regulations;
- IEC provisions in force;
- Fire Brigade provisions.
ASSEMBLY
Assembly, installation and maintenance must all be
done by contractors authorized by the local Gas Board
in accordance with the regulations in force. Before doing
anything else, contact your Gas Board.
Installation procedure
ISTRUZIONI PER L'INSTALLAZIONE
To level the appliance correctly, adjust the height of the
four adjustable feet.
Gas connection
The 3/4" G or 1/2" G gas pipe union can either be
permanently fixed or detached by using a standard
adaptor. If a flexible hose is used, it must be stainless steel
and in conformity with regulations. After completing
the connection, check for leaks by using a special leak-
detector spray.
Exhaust system
The appliances must be positioned in locations adapted
with a system for discharging the products of combustion
in respect of how much is prescribed by the norms of the
installation; such a system must comply with installation
regulations. Our appliances are classified as type "A1"
gas units (see the "TECHNICAL DATA" table). They are not
designed for the connection to a line for the discharge of
products of combustion.
These appliances must discharge the products of
combustion into appropriate hoods, or similar devices,
connected to a flue of proven efficiency, or they may be
connected directly to an outdoor vent.
If such an arrangement is not possible, the unit may be
connected to an air exhaust system which leads directly
outdoors, having a capacity no lower than required;
see the "TECHNICAL DATA" table, plus the air exchange
necessary, in order to make operators comfortable.
INSTALLATION
Before installation
Before installing the appliance, remove the protective
wrapping. Thoroughly clean the work-surface and the
outside of the appliance with lukewarm water and
detergent, using a soft cloth. Dry with a clean cloth.
Start-up
Before starting the appliance, make sure that its
specifications (category and type of gas used) match those
of the family and group of the gas available locally.
If not, adapt the appliance to the gas family or group
required (see paragraph "Running the appliance on other
types of gas"). Carry out the start-up according to the
User's Instructions.
Testing power rating
Use the nozzles for rated output on the appliances.
Capacity can be of two types:
- rated output, as given on the data plate;
| 67
EN