Dealer Service And Adjustment; Dealer Service Introduction; Critical Maintenance Tips; C.cleaning - Sunrise Medical Zippie ZONE Manual De Instrucciones

E N G L I S H
The owner of this chair is responsible for makiing sure that it has been setup and adjusted by a trained serv-
ice professional under the advice of a healthcare advisor. Service and/or adjustments should only be done
with the advice of a healthcare professional. Always use parts and/or accessories that have been recom-
mended and approved by Sunrise Medical when servicing this chair.
A. DEALER SERVICE INTRODUCTION
1. At least once per year, this chair should have a complete inspection, safety check, and regular service
made by an authorized dealer.
2. Torque settings– A torque setting is the optimum tightening which should be made on a particular fas-
tener. It is important to use proper torque settings where specified. When not specified, torque set-
tings should be 60 in-lbs
3. If you have discovered a worn, bent, or damaged part, repair or replace them with recommended
parts before returning this chair to service..
4. All major maintenance and repair work should be done by the authorized dealer.
B. CRITICAL MAINTENANCE TIPS
1. Torque settings:
A torque setting is the optimum tightening which should be made on a particular fastener. It is important to
use proper torque settings where specified. When not specified, torque settings should be 60 in-lbs
2. Dealer Service and Adjustment Reference materials:
Go to www.sunrisemedical.com for parts manuals, instruction sheets, and instructional videos that will aid in
the repair of the Zippie Family of wheelchairs.
C. CLEANING
1. Paint Finish
a. Clean the painted surfaces with mild soap or detergent.
b. Protect the paint with a coat of non-abrasive auto wax.
2. Axles and Moving Parts
a. Clean around axles and moving parts with a slightly damp (not wet) cloth.
b. Wipe off or blow away any fluff, dust or dirt on axles or moving parts.
c. DO NOT USE 3 in 1 oil, or WD-40 ® for lubrication. Only use Teflon based Lubricant when working
on this wheelchair.
D. REAR AXLE
The most important adjustment on your Zippie wheelchair is the position of the rear axle.
The center of gravity and wheel camber are determined by the axle adjustment.
1. Center of Gravity Adjustment
The more you move your rear wheels forward, the more likely your chair will tip
over backwards. Always make adjustments in small increments, and check the
stability of your chair with a spotter to prevent a tip-over. We recommend that
you use anti-tip tubes until you adapt to the change and are sure you are not at
risk to tip over. Refer to additional Warnings in Section VI "Falls and Tip Over".
NOTE– Changes to the center of gravity may affect the rear seat height (Section J), toe-in/toe-out of the rear
wheels (Section L-3) and the squareness of the casters (Section N). If you change your center of gravity
position, re-adjust all of these settings if necessary.
NOTE– Adjusting your chair's center of gravity will require re-adjusting the location of the wheel locks
(if provided). See Section P for instructions on adjusting the wheel locks.
You can adjust your center of gravity position by moving the camber clamp (C) fore or aft of
the axle plate (A). Using a 4mm Allen Key remove the bolt (B) from both the left and right
side of the wheelchair. Position the camber clamp in the new preferred center of gravity
location. Secure bolt back into position using 62 in-lbs. (7 Nm) of torque.
Ensure both sides of the wheelchair are using the same center of gravity position settings.
Once the axle plate and camber clamp are secured, attach the rear wheels, occupy the chair
and maneuver it with a spotter to get a feel for the new adjustment.
116100 Rev. D
WARNING
25
WARNING
IX. DEALER SERVICE AND ADJUSTMENT
20
TOOLS YOU WILL NEED
1. Imperial Hex key set
2. Metric Hex key set
3. Imperial Open-end Wrench set
4. Metric Open-end Wrench set
5. Torque wrench
6. Imperial Hex bit Socket set
7. Metric Hex bit Socket set
8. Phillips and Flat screwdrivers
25
A
B
C