DeWalt DCG413 Manual De Instrucciones página 14

English
Mounting Non-Hubbed Wheels (Fig. G)

WARNING: Failure to properly seat the flanges and/or
wheel could result in serious injury (or damage to the
tool or wheel).

CAUTION: Included flanges must be used with
depressed center Type 27/42 grinding wheels and
Type 1/41 cutting wheels. See the Accessories Chart
for more information.

WARNING: A closed, two-sided cutting wheel guard
is required when using abrasive cutting wheels or
diamond coated cutting wheels.

WARNING: Use of a damaged flange or guard or fail-
ure to use proper flange and guard can re sult in injury
due to wheel breakage and wheel contact. See the
Accessories Chart for more information.
1. Place the tool on a table, guard up.
2. Install the backing flange
raised center (pilot) facing the wheel. Press the backing
flange into place.
3. Place wheel 18 against the backing flange,
centering the wheel on the raised center (pilot) of the
backing flange.
4. While depressing the spindle lock button and with the
hex depressions facing away from the wheel, thread the
locking flange 7 on spindle so that the lugs engage the
two slots in the spindle.
5. While depressing the spindle lock button, tighten the
locking flange 7 by hand or using the wrench supplied.
(Only use a locking flange if it is in perfect condition.)
Refer to Accessory Chart to see flange details.
6. To remove the wheel, reverse the above procedure.
Fig. G
Mounting Sanding Backing Pads
(Fig. A, H)
nOTE: Use of a guard with sanding discs that use backing
pads, often called fiber resin discs, is not required. Since a
guard is not required for these accessories, the guard may or
may not fit correctly if used.

WARNING: Failure to properly seat the clamp nut
and/or pad could result in serious injury (or damage
to the tool or wheel).
12
on spindle with the
6 4
7
18
6
4

WARNING: Proper guard must be reinstalled for
grinding wheel, cutting wheel, sanding flap disc,
wire brush or wire wheel applications after sanding
applications are complete.
1. Place or appropriately thread backing pad
the spindle.
2. Place the sanding disc 19
3. While depressing spindle lock button
sanding clamp nut 17 on spindle, piloting the raised
hub on the clamp nut into the center of san ding disc
and backing pad.
4. Tighten the clamp nut by hand. Then depress the
spindle lock button while turning the sanding disc until
the sanding disc and clamp nut are snug.
5. To remove the wheel, grasp and turn the backing
pad and sanding pad while depressing the spindle
lock button.
Fig. H
Mounting and Removing Hubbed
Wheels (Fig. A)
Hubbed wheels install directly on the spindle. Thread of
accessory must match thread of spindle.
1. Remove backing flange by pulling away from tool.
2. Thread the wheel on the spindle
3. Depress the spindle lock button
tighten the hub of the wheel.
4. Reverse the above procedure to remove the wheel.
NOTICE: Failure to properly seat the wheel before
turning the tool on may result in damage to the tool
or the wheel.
Mounting Wire Cup Brushes and
Wire Wheels (Fig. A)

WARNING: Failure to properly seat the brush/wheel
could result in serious injury (or damage to the tool
or wheel).

CAUTION: To reduce the risk of personal injury,
wear work gloves when handling wire brushes
and wheels. They can become sharp.

CAUTION: To reduce the risk of damage to the
tool, wheel or brush must not touch guard when
mounted or while in use. Undetectable damage
could occur to the accessory, causing wires to
fragment from accessory wheel or cup.
on
15
on the backing pad 15 .
3 , thread the
17
19
15
by hand.
4
and use a wrench to
3