Kärcher B 110 R Manual Del Usuario página 24

Malfunction
fresh water empty
water valve blocked
overload brush head
blocked main brush
overload side brush
blocked side brush
waste water tank full
overload drive motor
blocked drive motor
battery low
battery empty
seat switch open
switch on!
restart machine
release throttle
Malfunction
The device cannot be started
The device is no longer running, dis-
play shows "battery empty"
The device moves unevenly (jerks)
when starting and stopping.
The water volume is insufficient
The fresh water display shows the
wrong filling level after emptying the
tank manually.
The bar of the filling level display is
flashing, "fresh water empty" display
The suction performance is too low
The cleaning results are unsatisfacto-
ry
24
Rectification
1. Refill the fresh water tank
1. Set the programme switch to "OFF".
2. Wait 10 seconds.
3. Set the program switch to the desired program.
1. Reduce the contact pressure of the brushes.
1. Check if the brushes are blocked by a foreign body and remove the foreign body if necessary.
2. Set the programme switch to "OFF".
3. Wait 10 seconds.
4. Set the program switch to the desired program.
1. Reduce the contact pressure of the side scrubbing deck brush.
1. Check if the brushes are blocked by a foreign body and remove the foreign body if necessary.
2. Set the programme switch to "OFF".
3. Wait 10 seconds.
4. Set the program switch to the desired program.
1. Empty the waste water tank.
1. The gradient is too steep.
a In cleaning operation: Cancel cleaning.
b When transporting: Find a path with a lower gradient.
1. Check the wheels for blockage, remove foreign objects.
2. Set the programme switch to "OFF".
3. If the engine has overheated, let it cool down for at least 15 minutes, otherwise wait 10 seconds.
4. Set the program switch to the desired program.
1. Set the program selector switch to TRANSPORT MODE.
2. Drive the device directly to the charger (or with an internal charger to the socket). Avoid gradients.
3. Charge the battery.
1. Set the program selector switch to TRANSPORT MODE.
2. Drive the device by the shortest route to the charger (or to the socket in the case of an internal charger). Avoid gradients.
3. Charge the battery.
1. Relieve the driver's seat briefly so that the control can check the function of the seat contact switch.
1. Set the safety switch to "1".
1. Set the programme switch to "OFF".
2. Wait 10 seconds.
3. Set the program switch to the desired program.
1. Release the accelerator pedal.
Malfunctions without information shown on the display
Rectification
1. Sit in the driver's seat.
2. Take your foot off the accelerator before switching on the safety switch.
3. Turn the safety switch to "1".
4. Check the battery and charge if necessary.
5. Set the programme switch to "OFF".
6. Wait 10 seconds.
7. Set the program switch to the desired program.
8. If possible, only drive the device on level ground.
9. Check the parking brake if necessary.
If the fault still occurs, call Customer Service.
1. Set the programme switch to "OFF".
2. Wait 10 seconds.
3. Set the program selector switch to "TRANSPORT MODE".
4. Drive to the charging station.
5. If the device still does not run, charge the battery on site or unlock the brake (see "Operation/pushing the device") and push
the device to the charging station.
1. Unlock the brake lock (see "Operation/pushing the device").
1. Check the fresh water filling level, if necessary fill the tank completely so that the air is pressed out.
2. Remove and clean the fresh water filter.
3. Insert the filter and screw on the cap.
4. Only with R cleaning head: Pull off the water distribution strip on the cleaning head.
5. Only with R cleaning head: Clean the water channel.
6. Check the hoses for clogging and clean if necessary.
1. Use the device. During operation, the hose system will vent and the filling level display will correct itself.
1. Refill the fresh water tank.
1. Clean the seals between the waste water tank and the cover, check for leaks and replace if necessary.
2. Check the fluff filter for soiling and clean if necessary.
3. Clean the suction lips at the suction bar, turn over or replace if necessary.
4. Close the lid on the waste water drain hose.
5. Close the cover of the waste water tank rinsing system.
6. Check the suction hose for clogging and clean if necessary.
7. Check the suction hose for leaks and replace if necessary.
8. Check the adjustment of the suction bar.
1. Set the appropriate cleaning program for the cleaning task.
2. Use suitable brushes for the cleaning task.
3. Use a suitable detergent for the cleaning task.
4. Reduce the driving speed.
5. Adjust the contact pressure.
6. Adjust the squeegee blades.
7. Check the brushes for wear and replace if necessary.
8. Check the water output.
English