Idiomas disponibles
Idiomas disponibles
• Give these safety regulations to all persons who
work on the machine.
• Caution! Hands and fingers may be injured on the
rotating saw blade.
• The machine is equipped with a safety circuit-break-
er to prevent it starting up again after a voltage drop.
• Before you use the machine for the first time, check
that the voltage marked on the rating plate is the
same as your mains voltage.
• If you need to use an extension cable, make sure its
conductor cross-section is big enough for the saws
power consumption. Minimum cross-section 1,5
mm² or 2,5 mm² for cable lengths of 20 m or more.
• If you use a cable reel, the complete cable must be
pulled off the reel.
• Check the power cable. Never use a faulty or dam-
aged power cable.
• Do not use the cable to pull the plug out of the sock-
et. Protect the cable from heat, oil and sharp edges.
• Do not leave the saw in the rain and never use it in
damp or wet conditions.
• Provide good lighting.
• Do not saw near flammable liquids or gases.
• Wear suitable work clothes! Loose garments or jew-
ellery may become caught up in the rotating saw
blade.
• Non-slip shoes are recommended when working
outdoors.
• Wear a hair net if you have long hair.
• Avoid abnormal working postures.
• Operators must be at least 16 years of age.
• Keep children away from the machine when it is con-
nected to the power supply.
• Keep your workplace clean of wood scrap and any
unnecessary objects.
• An untidy work area invites accidents.
• Do not allow other persons, especially children, to
touch the tool or cable. Keep them out of your work
area.
• Persons working on the machine should not be dis-
tracted.
• Note the direction of rotation of the motor and saw
blade. Use only blades whose permissible maximum
speed is not lower than the maximum spindle speed
of the circular saw and of the material to be cut.
• After you have switched off the motor, never slow
down the saw blade by applying pressure to its side.
• Only fit blades which are well sharpened and have
no cracks or deformations.
• Do not use circular saw blades made of high-alloy
high-speed steel (HSS).
26 | GB
• Only use saw blades that are recommended by the
manufacturer, comply with EN 847-1 and bear a
warning note.
• When replacing the saw blade ensure that the cut-
ting width is no smaller than the blade thickness of
the saw blade.
• Faulty saw blades must be replaced immediately.
• Never use saw blades which do not comply with the
data specified in this manual.
• Never dismantle the machines safety devices or ren-
der them inoperative.
• Always stand to the side of the saw blade when
working with the saw.
• Never load the machine so much that it cuts out.
• Make sure that off-cuts do not catch on the saw
blade crown. Risk of catapulting!
• Never remove loose splinters, chips or jammed piec-
es of wood when the saw blade is running, unless a
push stick is used.
• To rectify faults or remove jammed pieces of wood,
always switch off the machine first. Pull the power
plug!
• Carry out retooling work, adjustments, measure-
ments and cleaning jobs only when the motor is
switched off. Pull the power plug!
• Before switching on, make sure that all keys and
wrenches have been removed from the tool.
• Switch off the motor and pull the power plug before
you leave the workplace.
• Refit all guards and safety devices immediately af-
ter you have completed any repairs or maintenance
work.
• Be sure to observe the safety information and op-
erating and maintenance instructions issued by the
manufacturer, as well as the dimensions listed in the
Technical Data.
• It is imperative to observe the accident prevention
regulations in force in your area as well as all other
generally recognized rules of safety.
• Note the information published by your professional
associations (VBG 7j).
• The circular saw has to be connected to a 230 V
socket with a 16 A fuse.
• Do not use any low-powered machines for heavy
duty work.
• Do not use the cable for purposes for which it is not
designed.
• Make sure you stand squarely and keep your bal-
ance at all times.
• Check the tool for damage.
www.scheppach.com
