Midi Settings; Synchronizing Audio Signals To External Sequencer, Or Using Djm-800 Information To Operate An External Sequencer; Midi Messages - Pioneer DJM-800 Manual De Instrucciones

MIDI SETTINGS

MIDI is an acronym for "Musical Instrument Digital Interface" and
refers to a protocol developed for the exchange of data between
electronic instruments and computers.
A MIDI cable is used to connect components equipped with MIDI
connectors to enable the transmission and receipt of data.
The DJM-800 uses the MIDI protocol for transmitting and receiving
data about component operation and BPM (timing clock).
DJ CD Player
OUT
BPM
=120
Audio
IN
DJM-800

MIDI MESSAGES

Category Switch Name
CH1 TRIM
HI
MID
LOW
COLOR
CUE
FADER
CF ASSIGN
CH2 TRIM
HI
MID
LOW
COLOR
CUE
FADER
CF ASSIGN
CH3 TRIM
HI
MID
LOW
COLOR
CUE
FADER
CF ASSIGN
MIDI sequencer
IN
BPM
=120
MIDI OUT
MIDI START
/STOP
TIME
Switch Type
VR Bn
VR Bn
VR Bn
VR Bn
VR Bn
BUTTON Bn
VR Bn
SW Bn
VR Bn
VR Bn
VR Bn
VR Bn
VR Bn
BUTTON Bn
VR Bn
SW Bn
VR Bn
VR Bn
VR Bn
VR Bn
VR Bn
BUTTON Bn
VR Bn
SW Bn
SYNCHRONIZING AUDIO SIGNALS
TO EXTERNAL SEQUENCER, OR
USING DJM-800 INFORMATION TO
OPERATE AN EXTERNAL
SEQUENCER
1. Use a commercially available MIDI cable to connect the
DJM-800's MIDI OUT connector to the MIDI sequencer's
MIDI IN connector.
¶ Set the MIDI sequencer's synch mode to "Slave".
¶ MIDI sequencers that do not support MIDI timing clock cannot
be synchronized.
¶ Synch may not be achieved if the track's BPM cannot be
detected and measured stably.
¶ BPM values set with the TAP mode can also be used to output
the timing clock.
2. Press the MIDI START/STOP button.
¶ The MIDI timing clock output range is 40 to 250 BPM.
Note:
¶ Accurate measuring of BPM may be impossible with some tracks.
[MIDI Channel Setting]
The MIDI channel (1 to 16) can be set and stored in memory.
1. While holding the MIDI START/STOP button depressed,
set the power switch to ON.
¶ The display will show [MIDI CH SETTING] and the unit will
enter the MIDI setting mode.
2. Rotate the TIME dial to select the MIDI channel.
3. Press the MIDI START/STOP button.
¶ The selected MIDI channel will be recorded.
4. Set power to OFF.
MIDI Message
MSB LSB
01 dd
02 dd
03 dd
04 dd
05 dd
46 dd
11 dd
41 dd
06 dd
07 dd
08 dd
09 dd
0A dd
47 dd
12 dd
42 dd
0C dd
0E dd
0F dd
15 dd
16 dd
48 dd
13 dd
43 dd
MIDI SETTINGS
Comments
0 to 127
0 to 127
0 to 127
0 to 127
0 to 127
OFF=0, ON=127
0 to 127
0, 64, 127
0 to 127
0 to 127
0 to 127
0 to 127
0 to 127
OFF=0, ON=127
0 to 127
0, 64, 127
0 to 127
0 to 127
0 to 127
0 to 127
0 to 127
OFF=0, ON=127
0 to 127
0, 64, 127
19
<DRB1392>
En