Idiomas disponibles
Idiomas disponibles
D2160
Lubrication-free models:
• In the case of lubrication-free tools it is up to the
customer to decide on the peripheral equipment
to be used. However, it is no disadvantage if the
compressed air contains a small quantity of oil
e.g. supplied from a fog lubricator (DIM) or Dosol
system. This does not apply to turbine tools, which
should be kept oil free.
Compressed air connection
• The machine is designed for a working pressure
of 6–7 bar = 600–700 kPa = 87–102 psi.
• Blow out the hose before connecting.
Maintenance
Rust protection and internal cleaning
Water in the compressed air, dust and wear particles
cause rust and sticking of vanes, valves etc.
This can be prevented by flushing with oil (some
drops), running the tool for 5–10 seconds and absorb-
ing the oil in a cloth. Protect the tool this way before
longer standstills.
Overhaul and lubrication
The tool should be checked regularly at six-monthly
intervals. If it is in heavy duty service or not running
properly, it should be taken out of service more often
for inspection.
Regarding instruction for dismantling and as-
sembly, see separate Service Manual.
The throttle valve, planetary gears, needle bearings
and ball bearings must be lubricated with grease
when the tool is dismantled for the regular overhauls.
Molykote BR2 Plus gives long intervals between
lubrications.
A
Clean the motor parts and apply a thin layer
of gleitmo 585 KC grease (180 g – Ordering
No. 4080 0871 80) onto the vanes and inner
surface of cylinder and end plates.
Assemble the motor and check that it is run-
ning free. Add two drops of oil through the
air inlet and run the motor (machine) at idling
speed for 5-10 seconds.
The strainer in the adapter should be cleaned regu-
larly to prevent choking with resultant decrease in
capacity
EN
Lubricating guide for Grinder/ Sander
(except turbine) and Drill
Brand
BP
Castrol
Esso
Q8
Mobil
Shell
Texaco
Molycote
Useful information
You can find all kind of information concerning Pro
products, accessories, spare parts, published matters
on our WEB site!
C Log in to www.atlascopco.com/pro
Technical data
Noise and vibration emission
Noise (in accordance with ISO15744)
Sound pressure level
Sound power level
Uncertainty
Vibration total value, valid from 2010
(3-axes value in accordance with ISO28927-5)
Vibration value
Uncertainty
Vibration value, valid until 2009
(1-axis value in accordance with ISO8662-1)
Vibration value
Noise and Vibration Declaration State-
ment
These declared values were obtained by laboratory
type testing in accordance with the stated standards
and are suitable for comparison with the declared
values of other tools tested in accordance with the
same standards. These declared values are not ad-
equate for use in risk assessments and values meas-
ured in individual work places may be higher. The
actual exposure values and risk of harm experienced
by an individual user are unique and depend upon
the way the user works, the workpiece and the
workstation design, as well upon the exposure time
and the physical condition of the user.
© Atlas Copco Tools - 9836 4755 00
Safety and operating instructions
General purpose
Bearings
Energrease LS-EP2
Spheerol EP L2
Beacon EP2
Rembrandt EP2
Mobilegrease XHP 222
Alvania EP2
Multifak EP2
BR2 Plus
Air lubrication
Energol E46
Arox EP46
Chopin 46
Almo oil 525
Tonna R32
Aries 32
See "Lubrication" in
Operating instruc-
tions
dBA
80
-
3
2
m/s
<2.5
-
2
m/s
<2.5
5
