Bosch MCM4200 Instrucciones De Uso página 19

Cleaning the bowl and accessories
oáëâ=çÑ=áåàìêó=Ñêçã=ëÜ~êé=Ää~ÇÉë>
dêáé=íÜÉ=ìåáîÉêë~ä=Ää~ÇÉ=Äó=íÜÉ=ÉÇÖÉ=çÑ=íÜÉ=
éä~ëíáÅ=Ü~åÇäÉ=çåäóK=
tÜÉå=åçí=áå=ìëÉI=~äï~óë=éìí=íÜÉ=ìåáîÉêë~ä=
Ää~ÇÉ=Ä~Åâ=áåíç=íÜÉ=~ÅÅÉëëçêáÉë=Çê~ïÉêK
All parts are dishwasher-proof.
Do not wedge plastic parts in the dishwasher
as they could warp.
Cleaning the blender
oáëâ=çÑ=áåàìêó=Ñêçã=ëÜ~êé=Ää~ÇÉë>
aç=åçí=íçìÅÜ=ÄäÉåÇÉê=Ää~ÇÉë=ïáíÜ=Ä~êÉ=
Ü~åÇëK=`äÉ~å=íÜÉã=ïáíÜ=~=ÄêìëÜK
It is recommended to clean the blender
immediately after use. This will prevent residue
from drying on and attacking the plastic
(e.g. by essential oils in herbs).
The blender jug (without blade insert), lid and
funnel are dishwasher-proof.
Do not clean the blade insert in the dish-
washer, but under running water (do not
soak in water).
Tip: Pour a little water and washing-up liquid
into the attached blender. Switch to setting M
for several seconds. Pour out the water and
rinse the blender with clean water.
Taking the blender apart

Upon the wings, rotate the blade insert
in an anti-clockwise direction.
The blade insert is released.
 Take blade insert out and remove sealing
ring.
Putting the blender together
oáëâ=çÑ=áåàìêó>
kÉîÉê=~ëëÉãÄäÉ=ÄäÉåÇÉê=çå=íÜÉ=Ä~ëÉ=ìåáíK

Apply sealing ring on blade insert.

Insert blade insert from below into
blender jug.

Firmly screw on the blade insert
by the wings in a clockwise direction.
Rotate the blade insert at least until
a wing covers the mark on the blender
jug (position –> Fig.
Robert Bosch Hausgeräte GmbH

Fig.

6).
Cleaning the citrus press
All parts are dishwasher-proof. It is recommen-
ded to rinse the pressing cone immediately
after use on all sides under running water.
Doing so prevents residue from drying on.
Cleaning the juice centrifuge
To clean the juice centrifuge remove the filter
basket from the disc holder.
Pre-rinse parts under running water.
Carefully clean the slats of the filter basket
so as not to damage them.
Storing the appliance

Remove mains plug.

Stow the cord in the cord store.

Stow the tools in the accessories drawer.

Attach the bowl.
Note:
Take all accessory parts out of the bowl
and/or blender before use.
Only insert the parts needed.
Troubleshooting
oáëâ=çÑ=áåàìêó>
_ÉÑçêÉ=êÉÅíáÑóáåÖ=~=Ñ~ìäíI=éìää=çìí=íÜÉ=ã~áåë=
éäìÖK
Important information for
MCM42..
The Operating indicator flashes if the appli-
ance has been operated incorrectly or the
electronic fuse has tripped or the appliance
is defective.
Base unit
Fault:
Appliance does not work.
Possible cause:
The appliance was overloaded (e.g. tool
jammed by food) and the electronic fuse
has tripped.
Remedial action:

Set the rotary switch to 0/off.

Remove mains plug.
 Eliminate the cause of the overload.

Switch the appliance on again.
en

Fig.

Fig.
19