Cardin Elettronica SL Serie Manual Del Usuario página 15

- check that a mechanical travel limit "Q" (absolutely necessary) has been fitted in
the opening direction and that it corresponds to the maximum travel distance "P"
of the gate. The travel limit must guarantee anti-derailment and gate stability.
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
Warning! It is the installer's responsibility to check all critical danger
points, to take action and to install any devices needed to guarantee the
safety of all people using the gate (risk analysis).
INSTALLATION INSTRUCTIONS
• The geared motor can be positioned either to the left
or to the right of the passageway.
• The geared motor must be correctly positioned when
it is installed: perpendicular to the ground and straight
up on flat ground.
4
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
5
Gate
Toothed rack
Base plate
SCALA: 1:2
Drawing number : DI0237
Product Code : SL1524M
Draft : P.J.Heath Date : 30-01-2002
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
ANCHORING THE UNIT
Plan view
ANCHORING THE UNIT
Side view
SCALA: 1:2
All manuals and user guides at all-guides.com
b
C
Description : Prodotti Technocity
CONTROPIASTRA SL1524M
34 69
157
104,5
Anchoring the unit (fig. 4, 5, 6)
Important! Check the exact anchoring position with respect to the alignment of the
sliding gate.
• Run the piping and connection wires to the position where the motor is to be installed.
• Attach the anchor bolts to the base plate "A" allowing them to protrude by 50 mm
and then tighten down using the supplied M12 nuts.
• Prepare a cement plinth, in the position where the motor is to be installed, with a
depth of 350 mm (the base should protrude by about 25 mm to avoid damage by
pools of water building up under the appliance).
• Insert the base plate making sure that:
- the electrical cables pass through the hole "b";
- the anchor bolts "C" are immersed into the cement base and the base plate is
perfectly level;
- the four protruding threaded bolts are perpendicular to the base plate;
- the surface area of the base plate is clean and free of cement residue.
If the runner guide already exists the cement base should be extended to take in part
of the runner guide foundation. This will stop the two foundations from giving way
separately.
- Unscrew the four M12 nuts on the four threaded bolts (previously used to block the
All rights reserved. Unauthorised copying or use of the information contained in this do
anchor bolts) from the base of the anchor plate. Then insert the four washers and
allow them to rest on the nuts.
2
M 1
- Position the geared motor over the four threaded bolts and allow it to rest on the
four washers.
- Fasten in to the base using the other four washers and
adjustment nuts supplied with the kit, making sure that the unit remains perfectly
level and stable.
- Adjust the height if the unit using the four grub screws already positioned on the
motor. This will allow you to adjust the height and position of the motor later on.
A
Fitting the toothed rack
- release the geared motor (fig. 8), lay the first stretch of the toothed rack on the
pinion and fix it to the gate, then fasten down all the other parts along the entire
length of the gate.
- after having fastened the toothed rack, realign the pinion (play of 1 to 2 mm
between the toothed runner and the pinion) using the grub screws at the base
of the geared motor. This action will prevent the weight of the sliding gate from
damaging the unit when working.
6
INSTRUCTIONS FOR POSITIONING THE UNIT
SCALA: 1:2
Drawing number :
Product Code :
- The geared motor unit has been assembled in the factory
Draft : P.J.Heath
to be fitted to the LEFT SIDE of the gate (internal view).
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818
To install the motor to the RIGHT of the gate set dip 8 of
the dip-switch "DS1" (fig. 3) to "ON".
15
2 mm
7
Description :
DI0240
VISTA DI FIANCO CON MOT
SL1524
Date : 08-02-2002
Prodotti Technocity
ON
1 2 3 4 5 6 7 8 9