Tabla de contenido
1. SAFETY
Read the user manual carefully before using your appliance
for the first time.
1.1 IDENTIFICATION OF THE WARNINGS
MEANING
DANGER
This term defines a high risk of danger,
which can lead to death or serious in-
jury, if not avoided.
WARNING
This term defines a medium risk of
danger that can lead to minor to se-
rious injury, if not avoided.
NOTICE
This term defines dangers to the ma-
chine and its proper operation.
Warning of a general danger.
The danger is specified by indications
given in the table.
Warning about the dangers asso-
ciated with the electrical voltage and
provides information about protection
against electrical voltage.
Warning of damage to the boat.
1.2 GENERAL
DANGER
Electrical hazards and risks of cuts.
Never dismantle the appliance.
Don't use your appliance if a cable or connec-
tion plug is damaged.
To avoid danger, have repairs done by autho-
rised persons.
Connection errors (observe the polarity) or incorrect connec-
tion invalidate the warranty.
WARNING
Risk of cutting.
Never touch moving parts.
Incorrect use or installation releases SFA from any liability.
For further information, don't hesitate to contact our cus-
tomer service.
DISCONNECT THE ELECTRICAL POWER SUPPLY, BE-
FORE ATTEMPTING ANY WORK ON THE UNIT.
2. DESCRIPTION
2.1 APPLICATION
Sanimarin® Maxlite+ is a bowl fitted with a pump/macerator
to remove the sanitary effluent. It is also fitted with a self-pri-
ming sea water supply pump.
Sanimarin® Maxlite+ is a WC equipped with a pump/mace-
rator which installed and used correctly will give reliable and
consistent service for many years.
Sanimarin® Maxlite+ macerates and pumps effluents without
disinfecting effect.
THIS PRODUCT SHOULD NOT BE USED FOR ANY OTHER
PURPOSE OTHER THAN DESCRIBED HERE.
2.2 OPERATING MODE
Sanimarin® Maxlite+ is controlled by a two-position switch:
• Add water: bowl flushing command,
• Pump out: maceration and discharge command.
2.3 SCOPE OF SUPPLY
Sanimarin® Maxlite+ is supplied with an additional soft-
bladed impeller for the first maintenance.
Note: The impeller must be replaced annually. See §6
2.4 TECHNICAL DATA
Max. Pumping
3 m
height
Max. Horizontal
30 m
pumping distance
Supply voltage
12 V or 24 V
Outlet diameter
38 or 25 mm
Weight
8 kg
3. INSTALLATION
DANGER
Before you begin any work on this product,
make sure that:
- all electrical power to the unit has been
switched off
- and that the through-hull valves are in the
CLOSED or STOP position.
3.1 FIXING THE DEVICE
• Maxlite+ can be installed in place of a toilet with a manual
pump.
• Fix Maxlite+ securely using the screws provided. Your
mountings must be appropriate for the base on which the
device is to be installed.
Note: You can turn Maxlite+ bowl to suit your requirements
and the space available (see installation instructions).
• Observe the pumping direction (arrows) when turning the
unit over.
• Preparing to mount the rocker switch: cut out a 40 mm x 25
mm rectangular panel.
3.2 CONNECTING THE EVACUATION
IMPORTANT
Pollution risk.
All boats built from 2008 onwards must be
equipped with a black water recovery tank. Favour
the emptying of black water tanks thanks to the
installations provided in the ports.
Please check local legislation regarding discharge
from on board toilets- i.e. holding tanks etc.
A seacock should be fitted where the Sanimarin® Maxlite+
discharges through a skin fitting.
DANGER
For units installed below the water line, the
discharge pipe should rise at least 50 cm above
water level and be fitted with an anti-syphon valve
prior to falling and discharging through the skin fit-
ting.
The device outlet is fitted with a non-return valve.
The outlet diameter is 38 mm (if necessary an adapter for
25 mm is provided in the accessory bag).
3.3 CONNECTING THE SEA WATER SUPPLY
First determine whether the sea water supply to the Maxlite+
will be above or below the water-line, and then proceed with
the installation instructions.
If the installation of the toilet requires the use of through-hull
valves below the waterline, it is essential to follow the fitting
instructions provided by the manufacturer of the through-
hull valve.
Access to the valves should be easy for all users of the toi-
let. If this is not the case, additional full flow marine quality
valves should be installed on the water inlet and outlet.
• Connect your water feed pipe from the through-hull valve
to the built-in self-priming pump (19 mm inner diameter).
DANGER
All vented loops (not supplied with the toilet) must
be installed a minimum of 50 cm above the waterline.
9
EN
Component materials
Bowl
Copolyester
Base
Polyamide
Tabla de contenido
