Preparation For Operation - VERTO 52G684 Manual De Uso

• If the power cord gets damaged during operation, disconnect the
power supply immediately. DO NOT TOUCH POWER CORD BEFORE
DISCONNECTING FROM THE POWER SUPPLY.
• If the saw is equipped with laser, replacement with laser of another
type is forbidden and all repairs must be carried out by the service. Do
not aim the laser beam at people or animals.
• Do not use the tool in stationary mode. It is not designed for use with
sawing table.
• Fix processed material to stable surface and secure with clamps or
vice to eliminate shifting. This kind of work piece fixation is safer than
holding the work piece in hand.
• Wait until blade comes to a complete stop before putting the power
tool away. Cutting blade may jam and cause loss of control over the
power tool.
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is always
a small risk of operational injuries.
SAFETY RULES FOR LASER DEVICE
Laser device used in the saw design is the class 2 with maximum
power below 1 mW and wavelength λ = 650 nm. Such device is not
dangerous to your sight, however do not look directly at the source
of the light (temporary blindness hazard).
WARNING. Do not look directly at the source of laser beam. It
may cause hazards. Follow the below safety rules.
• Use the laser device in accordance with the manufacturer's
instructions.
• Do not, either intentionally or unintentionally, point the laser
beam at people, animals or any object other than processed
material.
• Do not bring to accidental pointing the laser beam at bystanders'
or animals' eyes for a period longer than 0.25 second, for instance
by pointing the laser beam at mirrors.
• Always ensure the laser beam is directed at material which does
not have any reflective surfaces.
• Reflective steel sheet (and other materials with reflective surface)
does not allow for laser use, because it might cause hazardous
light reflection directed at operator, bystanders or animals.
• Do not replace laser unit with device of other type. All repairs must
be carried out by the manufacturer or authorized person.
CAUTION: Adjustments other than described in this manual put
in danger of exposition to laser radiation
CONSTRUCTION AND USE
Circular saw is a hand-held power tool with insulation class II. It is
driven by a single-phase commutator motor. This type of power
tools is widely used for cutting wood and objects made of wood-
like materials that match with the tool size. Do not use the saw for
cutting firewood. Attempts to use the circular saw for purposes
other than specified will be considered an improper use. Use the
circular saw only with appropriate cutting blades with teeth with
sintered carbide tips. Circular saw is designed for light duty works in
service workshops and any individual, amateur activities (tinkering).
Use the power tool according to the manufacturer's instructions
only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
a. Dust extraction outlet
b. Upper guard
c. Lower guard lever
d. Parallel guide locking knob
e. Saw base
f. Cutting blade
g. Collar washer
LASER LIGHT, LASER RADIATION
DO NOT LOOK AT THE LASER BEAM
LASER DEVICE CLASS 2
Wavelength: 650 nm; Output: < 1 mW
EN 60825-1:2014
h. Bolt for cutting blade fixing
i. Lower guard
j. Spindle lock button
k. Front handle
l. Cutting depth locking lever
m. Switch
n. Switch lock button
o. Main handle
p. Brush cover
q. Knob for base bevel adjustment
r. Laser switch
s. Battery compartment
t. Laser
* Differences may appear between the product and drawing
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY/SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
1. Parallel guide
2. Hexagonal key

PREPARATION FOR OPERATION

CUTTING DEPTH ADJUSTMENT
Cutting depth can be set from the range of 0 to 65 mm.
• Loosen the cutting depth locking lever (12).
• Set desired cutting depth (use the scale).
• Lock the cutting depth locking lever (12) (fig. A).
INSTALLATION OF GUIDE FOR PARALLEL CUTTING
Use parallel guide when cutting material to narrow pieces. Guide
can be installed on left and right side of the power tool.
• Loosen the parallel guide locking knob (4).
• Insert parallel guide bar into two holes in the saw base (5).
• Set desired distance (use the scale).
• use the parallel guide locking knob to fix the parallel guide (4).
The parallel guide can also be used for cutting at angles ranging
from 0 0 to 45 0 .
Never put hand or fingers behind the working saw. When kick
back happens the saw can fall on the hand, it may be the cause
of heavy body injury.
MOVING THE LOWER GUARD
Lower guard (9) of cutting blade (6) is pushed away automatically as
the blade deepens into the material.
To remove it manually push the lower guard lever (3).
DUST EXTRACTION
Circular saw is equipped with dust outlet (1) that allows for
extraction of sawdust produced when cutting.
OPERATION / SETTINGS
SWITCHING ON / SWITCHING OFF
The mains voltage must match the voltage on the rating plate of
the circular saw. Hold the saw with both hands when starting up,
because engine turning moment may cause uncontrolled turn of
the power tool.
Remember that rotating parts of the saw rotate for some time
after the tool has been switched off.
The saw is equipped with the switch lock button (14) that protects
against accidental starting.
Switching on:
• Press the switch lock button (14) (fig. B).
• Press the switch button (13).
Switching off:
• Release pressure on the switch button (13).
12
- 1 pce
- 1 pce