GGP ITALY SBC 425 H Manual De Instrucciones página 105

Mount the components very carefully so as
not to impair the safety and efficiency of the
machine. If in doubt, contact your dealer.
WARNING! Unpacking and completing
the assembly should be done on a flat and
stable surface, with enough space for moving
the machine and its packaging, always mak-
ing use of suitable equipment.
Disposal of the packaging should be done in ac-
cordance with the local regulations in force.
1.1 COMPLETING THE MACHINE
1.1a. Models SBC 425 H - 435 H (Fig. 1)
– S lide the contoured plate (1) until it is close to
the holes in the drive tube (2).
– F it the top part (3) of the front handgrip on the
plate (1) so that the pin (4) fits into one of the
three holes provided on the drive tube (2) to
adjust the handgrip to the operator's prefer-
ence.
– J oin the bottom part (5) with the guard and at-
tach it to the top part (3), tightening the screw
(6) completely.
1.1b Models SBC 425 HD - 435 HD (Fig. 2)
– U nscrew the middle knob (1) and remove the
cap (2).
– I nsert the handle bar (3), making sure that the
controls are on the right.
– S et the handle bar in the most comfortable
working position and lock it using the cap (2)
and knob (1).
– F asten the casing (4) of the controls to its ca-
ble fastener (5).
NOTE Loosening the knob (1) the handle bar can be rotated to reduce its bulk for storage.
1.2 FITTING THE GUARD ON THE CUTTING
DEVICE (Fig. 3)
WARNING! Each cutting device is pro-
vided with a specific guard. Never use guards
other than those indicated for each cutting
device.
WARNING! Wear protective gloves and
fit the blade guard.
– R emove the screw (1) from the guard (2).
– I nsert the tab (3) in the guard seat (2) and fas-
All manuals and user guides at all-guides.com
1.3 FITTING AND REMOVING CUTTING
ting devices or ones homologated by the
Manufacturer.
1.3.1 Selecting the cutting device
Choose the most suitable cutting device for the
job to be done, according to these general indi-
cations:
– the 3-point blade is suitable for cutting brush-
– the 4-point blade is suitable for cutting tough
– the cutting line head can eliminate tall grass
Every cutting device must be fitted with a specif-
ic guard, as indicated by the following directions.
IMPORTANT The cutting devices are fastened
with a left-hand thread and therefore must be un-
screwed clockwise and screwed on anticlock-
wise. Remove all elements that may have been
assembled, which will be used in various con-
figurations, according to the cutting device used.
1.3.2 3 or 4-point blade "Tri-Arc" blade"
a) Assembly
– F it the inner ring-nut (1) in the indicated direc-
– F it the blade (3) and the outer ring-nut (4), with
– I nsert the supplied wrench (5) in the specific
– F it the cup (6) fully tightening the nut (7) anti-
– R emove the wrench (5) to restore rotation.
b) Adjusting the guard
– R emove the additional guard (8 - if already fit-
c) Disassembly
13
ten the guard with the screw (1).
DEVICES AND PREPARING GUARDS
WARNING! Use only
wood and small shrubs up to 2 cm in diameter;
grass over large surfaces;
and non-woody vegetation near fences, walls,
foundations, pavements, around trees, etc. or
completely clean a particular area of the gar-
den;
(Fig. 4)
tion, making sure that the inner ring-nut's (1)
grooves match perfectly with those of the an-
gle transmission (2).
the flat part toward the blade.
hole, then turn the blade (3) by hand and push
the wrench (5) until it enters the hole of the an-
gle transmission (2), blocking rotation.
clockwise (25 Nm).
ted), unhooking hooks clicked into the guard
(9).
original cut-