Gwarancja I Serwis - VERTO 52G682 Instrucciones De Uso

GWARANCJA I SERWIS

Warunki gwarancji oraz opis postepowania w przypadku reklamacji
zawarte są w załączonej Karcie Gwarancyjnej.
Serwis Centralny
GTX Service
Ul. Pograniczna 2/4
02-285 Warszawa
Sieć Punktów Serwisowych do napraw gwarancyjnych
i pogwarancyjnych dostępna na platformie internetowej
gtxservice.pl
Grupa Topex zapewnia dostępność części zamiennych oraz
materiałów eksploatacyjnych dla urządzeń i elektronarzędzi.
Pełna oferta części i usług na gtxservice.pl. Zeskanuj kod QR i wejdź:
tel. +48 22 573 03 85
fax. +48 22 573 03 83
e-mail [email protected]
GB
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
CAUTION: BEFORE USING THE POWER TOOL READ THIS MANUAL
CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
DETAILS OF OPERATIONAL SAFETY FOR CIRCULAR SAWS
WITHOUT SPLITTING WEDGE
DANGER
a. Keep your hands away from cutting area and cutting blade.
Keep the second hand on the secondary handle or the motor
casing. When holding the saw with both hands the risk of injury
with cutting blade is reduced.
b. Do not reach under the processed material. Guard does not
protect from rotating cutting blade below processed material.
c. Adjust cutting depth to thickness of processed material. It is
recommended that the cutting blade reaches below the processed
material no more than tooth-length.
d. Never hold processed material in hands, never keep it on
legs. Fix processed material to sound base. Good fixing of
processed material is important to avoid danger of contact with
body, rotating cutting blade being caught or loss of control over
the operation.
e. Hold the insulated surfaces of the saw that are designed for
such purpose when the rotating cutting blade can encounter
live wires or the wire that powers the saw. Contact of power
tool metal parts with live wire may cause operator's electric shock.
f. When ripping always use guide for ripping or edge guide. It
improves cutting accuracy and reduces risk of pinching the rotating
cutting blade in material.
g. Use only cutting blades with correct arbour hole diameter.
Cutting blades that do not match seating may operate with
eccentric offset, which causes loss of control over operation.
h. Never use damaged or incorrect washers or bolts to install
cutting blade. Washers and fixing bolts for cutting blade
installation were designed especially for circular saw to provide
optimal operation and safety of use.
i. Hold the circular saw firmly with both hands in position that
allows to resist kick-back. Stand to the side of the circular
saw but not in the line of cutting. Kick back may cause sudden
move to the back of circular saw but its force can be controlled by
operator when appropriate precaution measures are taken.
j. When the cutting blade jams or stops cutting, release the
switch button and hold the saw still in the material until the
blade stops completely. Never attempt removing the cutting
blade from material being cut nor pull the saw back when
the blade is rotating. It may cause kick back. Investigate and
implement correction procedures to eliminate causes of cutting
blade seizing.
k. When restarting the saw in the processed material, center
the cutting blade in the kerf and ensure the blade teeth are
not blocked in the material. When the cutting blade jams during
restart, it may slide off or cause kick back against the processed
material.
l. Support large boards to minimize risk of pinching and kick
back of the circular saw. Large boards tend to bend under own
weight. Place supports under board on both sides, close to the
cutting line and close to the board edge.
m. Do not use blunt or damaged cutting blades. Blunt or
incorrectly positioned blade teeth create narrow kerf, excessive
friction, jamming of cutting blade and kick back.
n. Firmly set clamps for cutting depth and bevel angle before
making a cut. Change of saw settings during cutting may cause
jamming and kick back.
o. Be very careful during in-depth cutting in division walls.
Cutting blade may encounter objects not visible from the outside
and cause kick back.
p. Ensure the lower guard is appropriately positioned before
10
CIRCULAR SAW
52G682