User Profiles (Pairing Porsche Id); Connecting To An Energy Manager; Hotspot; Adjusting The Charging Current - Porsche Mobile Charger Connect Manual De Instrucciones

Connection via WiFi
1. Select W F .
I I
2. Select the home network from the list of detected
WiFi networks.
3. Enter and confirm your password.
Connection via PLC pairling button
1. Select PLC .
PAIRLING BUTTON
2. Start the connection process on the PLC adapter.
Confirm by pressing OK on the charger.
Once the setup is connected, confirm with
C .
ONNECT
The connection to the PLC network is active.
If a connection to the PLC network is established, the
symbol will be displayed in the status bar.
Connection via PLC security code
A device on which the control software for the PLC
network is installed must be used for this method.
1. To establish a connection to a PLC network using
the security code, select PLC
SECURITY CODE
The security code appears on the display.
2. Enter the security code in the relevant menu of
the control software for the PLC network in order
to integrate the charger into the PLC network.
The connection to the PLC network is active.
If a connection to the PLC network is established, the
symbol will be displayed in the status bar.

User profiles (pairing Porsche ID)

When the charger is paired to your Porsche ID,
information about the charger and the charging
processes can be displayed in My Porsche and in the
Porsche Connect app.
To pair the charger with your Porsche ID:
e Call up the web site specified on the display on
the charger in the browser on your device and
enter the user code.
– or –
e Scan the QR code displayed on the charger. You
can scan the QR code in the following ways:
– Using the Porsche Connect app (My Account
> Charging cables & devices > Scan QR code).
– Using the camera on your device (iOS 11 or
higher, different for Android).
– Using an app for scanning QR codes.
If the charger was paired successfully, the
installation assistant moves on to the next step.
Connect energy manager
A connection to an energy manager can be
established, if one is available. The energy manager
then assumes control of the charging process.
e For instructions for connecting, refer to the
operating instructions for the energy manager.
If there is no energy manager available, the vehicle
.
will be charged at the charging current entered on
the charger (S > A
ETTINGS
f Refer to chapter "Adapt charging current" on
page 31.

Hotspot

If it is not possible to integrate into a home network,
the charger can activate a hotspot, thereby
establishing a connection to the web application on
the charger.
e To activate a hotspot, click on A
Once a hotspot has been activated, the symbol
appears in the status bar.
Adapt charging current
The maximum permitted charging current for the
charger can be set here if there is no energy manager
available in the home network.
The displayed maximum value is determined by the
types of cable that are connected.
e Set the charging current to the maximum value
available in the mains supply used for the charger.
Use P
f Refer to chapter "Charging Current Limiting" on
page 33.

Device protection

To prevent an unauthorised vehicle from being
connected to the charger, a PIN prompt can be set
up.
1. To activate the PIN prompt, select O
2. Enter a 4-digit PIN and confirm.
3. Enter the PIN again and confirm.
Activation of the PIN prompt is confirmed.

Finishing the setup process

).
DAPT CHARGING CURRENT
e Check the settings you entered using S
and complete the installation.

Web Application

Additional configuration options and detailed
information on existing charging processes are
available using a web application designed
specifically for each charger.
.
CTIVATE HOTSPOT
Web Application
and M to do this.
LUS INUS
.
N
UMMARY
DE
EN
FR
IT
ES
PT
NL
SV
FI
DA
NO
EL
CZ
HU
PL
HR
SR
SK
SL
ET
LT
LV
RO
BG
MK
31