Important; Maintenance - Parkside PZKS 2000 B2 Instrucciones De Utilización Y De Seguridad

10.5 Crosscut 90° and turntable 0° - 45°
(fig. 1/7/8)
The crosscut, drag and mitre saw can be used to make cross-
cuts of 0° -45° to the left and 0° -45° to the right in relation
to the stop rail.

Important!

For 90° crosscuts, the moveable stop rail (16a) must be fixed
in the inner position.
• Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) inwards.
• The moveable stop rails (16a) must be locked so that the
distance between the stop rails (16a) and the saw blade (6)
is at least 8 mm.
• Before making the cut, check that the stop rails (16a) and the
saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Loosen the handle (11) if it is tightened. Pull the indexed po-
sition lever (35) upwards with the pointer finger. Adjust the
rotary table (14) to the desired angle using the handle (11).
• The pointer (12) on the rotary table must match the desired
angle on the scale (13) on the fixed saw table (15).
• Re-tighten the handle (11) to secure the rotary table (14).
• Cut as described under section 10.4.
10.6 Mitre cut 0°- 45° and turntable 0°
(fig. 1/2/11)
The crosscut, drag and mitre saw can be used to make mitre
cuts of 0° - 45° in relation to the work face.
Attention!
For bevel cuts (inclined saw head), the moveable stop rail
(16a) must be fixed in the outer position. (Left side).
• Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) outwards.
• The moveable stop rails (16a) must be locked so that the
distance between the stop rails (16a) and the saw blade (6)
is at least 8 mm.
• The moveable stop rail (28) must be fixed in the inner posi-
tion. (Right side).
• Before making a cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Move the machine head (4) to the top position.
• Fix the rotary table (14) in the 0° position.
• Loosen the set screw (22). Use the handle (1) to angle the
machine head (4) to the left, until the pointer (19) indicates
the desired angle measurement on the scale (18).
• Re-tighten the set screw (22).
• Cut as described in section 10.4.
10.7 Mitre cut 0°- 45° and turntable 0°- 45°
(fig. 1/2/4/12)
The crosscut, drag and mitre saw can be used to make mitre
cuts to the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 45° to the left or 0° - 45° to the right in
relation to the stop rail (double mitre cut).
Attention!
For bevel cuts (inclined saw head), the moveable stop rail
(16a) must be fixed in the outer position. (Left side).
• Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) outwards.
10 GB/IE
• The moveable stop rails (16a) must be locked so that the
distance between the stop rails (16a) and the saw blade (6)
is at least 8 mm.
• Before making a cut, check that the stop rails (16a) and the
saw blade (6) cannot collide.
• Re-tighten the set screw (16b).
• Move the machine head (4) to its upper position.
• Release the rotary table (14) by loosening the handle (11).
• Using the handle (11), set the rotary table (14) to the de-
sired angle (refer also to point 10.5 in this regard).
• Re-tighten the handle (11) to secure the rotary table (14).
• Undo the set screw (22).
• Use the handle (1) to tilt the machine head (4) to the left until
it coincides with the required angle value (in this connection
see also section 10.6).
• Re-tighten the set screw (22).
• Cut as described under section 10.4.

11. Maintenance

m Warning! Prior to any adjustment, maintenance
or service work disconnect the mains power plug!
11.1 General maintenance measures
Wipe chips and dust off the machine from time to time using a
cloth. In order to extend the service life of the tool, oil the rotary
parts once monthly. Do not oil the motor.
When cleaning the plastic do not use corrosive products.
11.2 Cleaning the moving saw blade guard safety
device (5)
Always check the saw blade guard for debris before using the
machine.
Remove old sawdust and splinters using a brush or similar tool.
11.3 Replacing the table insert
Danger!
With a damaged table insert (10) there is a risk of small parts
getting stuck between table insert and saw blade, blocking the
saw blade. Immediately replace damaged table in-
serts!
1. Remove screws at table insert. If required, turn rotary table
and incline saw head to be able to reach the screws.
2. Remove table insert.
3. Install new table insert.
4. Tighten the screws at table insert.
11.4 Brush inspection
Check the carbon brushes after the first 50 operating hours
with a new machine, or when new brushes have been fitted.
After carrying out the first check, repeat the check every 10
operating hours.
If the carbon is worn to a length of 6 mm, or if the spring or
contact wire are burned or damaged, it is necessary to replace
both brushes. If the brushes are found to be usable following
removal, it is possible to reinstall them.
When servicing the carbon brushes, open the two latches coun-
terclockwise (as shown in Figure 21). Then remove the carbon
brushes.
Replace the carbon brushes in the reverse order.