Explanation Of Symbols; Technical Data - REMS CamScope Instrucciones De Servicio

eng

Explanation of symbols

Read the operating instructions before use
Power tool complies with protection class II

1. Technical Data

The REMS CamScope and REMS CamScope S endoscope camera is used for the inspection and damage analysis of locations with difficult access such as cavities,
shafts, pipes etc. and serves for documenting the inspection results in the form of photos and videos, in the REMS CamScope S in the form of videos with voice
recording. The camera cable sets of REMS CamScope and REMS CamScope S are protected against temporary immersion in water (≤ 30 min, ≤ 0.1 bar).
1.1. Supply Format
REMS CamScope
REMS CamScope S
* Supply format:
Handheld unit, 4 batteries 1.5V, AA, LR6, controller unit, MicroSD-card 2 GB, power supply/charger unit, USB-cable, video cable, case
1.2. Accessories
Camera cable set Color 16-1
Camera cable set Color 9-1
Camera cable set Color 4.5-1
900 mm push cable extension
1.3. Handheld Unit
Transmission frequency
Modulation type
Bandwidth
Radio transmission range
Power supply
Dimensions
Weight
1.4. Controller Unit
Display
Pixels (display)
Pixels (recording)
Video system
Reception frequencies
Transmission channel
Rechargeable batteries
Power supply / charger unit
Video level
Video rate
Frame rate
Zoom
Dimensions
Weight
Temperature range
Humidity
1.5. Camera Cable Set Color
Image sensor
Number of pixels
Viewing angle
Focus range
Min. lighting
Power supply
Dimensions
Weight
Video format
Type of protection camera
2. Start-up
Remove the screw from the battery compartment (17) of the handheld unit (5)
(only in REMS CamScope), push the cover in the direction of the arrow to
remove, remove the battery holder, insert 4 1.5 V, AA, LR6 batteries into the
battery holder, pay attention to the position of the plus-minus poles. Push the
battery holder back into the battery compartment, slide in the cover, screw in
the screw (only in REMS CamScope). Always change all four batteries at once.
The controller unit has an integrated Li-Ion battery. Caution: Mains voltage
present! Charge the controller battery before start-up. To do so, connect the
supply voltage/Li-Ion charger to the charger/mains socket (16) of the controller
unit and a suitable wall socket. The battery charging time is approximately 3
hours. A full charge lasts for about 2 hours of operation depending on the use.
The controller unit can also be operated with the connected supply voltage/
charger.
Set 16-1
175110
* Supply format
Camera cable set Color 16-1
Add-on mirror, add-on hook
Add-on magnet
175130
* Supply format
Camera cable set Color 16-1
Add-on mirror, add-on hook
Add-on magnet
175103
175104
175102
175105
REMS CamScope
2,468 MHz
FM
18 MHz
up to 10 m
4 batteries 1.5 V, AA, LR6
190 × 140 × 40 mm
260 g
REMS CamScope
3.5" Color TFT-LCD
320 × 240
640 × 480
PAL / NTSC
2414, 2432, 2450, 2468 MHz
4
integrated Li-Ion battery 3.7 V, 1.2 Ah
100 – 240 V AC, 50 – 60 Hz, Input /
5 V DC, 1 A, Output
0.9 – 1.3 Vpp on 75 Ohm
27 MB per minute
up to 30 frames per second
–
100 × 70 × 25 mm
130 g
–10°C ... +50°C / +14°F ... +122°F
15 – 85% RH
16 mm camera
CMOS
704 × 576
50°
60 – 350 mm
0 lux
by handheld unit
Ø 16 × 970 mm
280 g
PAL
IP 67
Environmentally friendly disposal
CE conformity mark
Set 9-1
175111
* Supply format
Camera cable set Color 9-1
Add-on mirror, add-on hook
Add-on magnet
175131
* Supply format
Camera cable set Color 9-1
Add-on mirror, add-on hook
Add-on magnet
REMS CamScope S
2,468 MHz
FM
18 MHz
up to 10 m
4 batteries 1.5 V, AA, LR6
190 × 165 × 53 mm
320 g
REMS CamScope S
3.5" Color TFT-LCD
320 × 240
640 × 480
PAL / NTSC
2414, 2432, 2450, 2468 MHz
not adjustable
integrated Li-Ion battery 3.7 V, 1.2 Ah
100 – 240 V AC, 50 – 60 Hz, Input /
DC 5 V / 1 A, Output
0.9 – 1.3 Vpp on 75 Ohm
27 MB per minute
up to 30 frames per second
1.5 / 2.0 / 3.0 ×
105 × 90 × 42 mm
240 g
–10°C ... +50°C / +14°F – +122°F
15 – 85% RH
9 mm camera
CMOS
640 × 480
36°
20 – 100 mm
0 lux
by handheld unit
Ø 9 × 970 mm
190 g
PAL
IP 67
Push the controller unit (7) onto the handheld unit (5) from above until it snaps
into place. When inserting the camera cable set (2), make sure that the pin on
the cable plug (3) is pushed into the slit in the cable socket on the handheld
unit (5). Tighten the knurled nut.
The controller unit can be operated both by radio signal and directly with the
handheld unit. If the controller unit (7) is fixed to the handheld unit (5), the signal
transmission takes place via the contact pins on the controller unit and on the
handheld unit. Transmission switches over to radio signal transmission as soon
as the controller unit is removed from the handheld unit. For radio-controlled
operation, make sure that the controller of the REMS CamScope is set to channel
CH 4. This is indicated in the top left hand corner of the display. If this setting
should deviate, it can be corrected to CH 4 by pressing the Down button (12)
several times. No channel must be set manually in the REMS CamScope S.
eng
Set 4.5-1
175112
* Supply format
Camera cable set Color 4.5-1
175132
* Supply format
Camera cable set Color 4.5-1
4.5 mm camera
CMOS
320 × 240
63°
10 – 50 mm
0 lux
by handheld unit
Ø 4.5 × 1030 mm
30 g
NTSC
IP 67