Safety-Related Information; Conventions In This Document; Description - Dräger CPS 7900 Instrucciones De Uso

Safety-related information

1 Safety-related information
Before using this product, carefully read these Instructions

for Use and those of the associated products.
Strictly follow the Instructions for Use. The user must fully

understand and strictly observe the instructions. Use the
product only for the purposes specified in the Intended use
section of this document.
Do not dispose of the Instructions for Use. Ensure that they

are retained and appropriately used by the product user.
Only trained and competent users are permitted to use this

product.
Comply with all local and national rules and regulations

associated with this product.
Only trained and competent personnel are permitted to

inspect, repair and
recommends a Dräger service contract for all maintenance
activities and that all repairs are carried out by Dräger.
Only authentic Dräger spare parts and accessories may be

used for maintenance. Otherwise the proper functioning of
the product may be impaired.
Do not use a faulty or incomplete product. Do not modify

the product.
Notify Dräger in the event of any product or component

fault or failure.
2

Conventions in this document

Meaning of the alert icons
The following alert icons are used in this document to identify
and highlight areas of text that require greater awareness by
the user. A definition of the meaning of each icon is as follows:
WARNING
!
Indicates a potentially hazardous situation. If not
avoided, this situation could result in death or serious
injury.
CAUTION
!
Indicates a potentially hazardous situation. If not
avoided, this situation could result in physical injury or
damage to the product or environment. It may also be
used to alert against unsafe practices.
NOTICE
i i
Indicates additional information on how to use the
product.
Brand names
The following brand names are used in this document:
® ® ®
D-mex , FPS , HPS

®
and X-plore are registered trademarks of Dräger.
® ®
Eltra and ECOLAB are registered trademarks of Ecolab.

®
K-MEX and Tricotril

KCL GmbH.
®
Barrier is a registered trademark of Ansell.

®
Cryo-Industrial is a registered trademark of Tempshield,

Inc.
Abbreviations
FKM = fluoroelastomer
22
service the product.
®
, Panorama Nova , PAS
®
are registered trademarks of
3

Description

Dräger CPS 7900 are gas-tight chemical protective suits
according to EN 943-2:2002 (Type 1a-ET). They are re-
usable.
A self-contained breathing apparatus is required for breathing
air supply. The compressed air breathing apparatus, full face
mask and safety helmet are worn under the chemical
protective suit. Possible combinations see Chap. 3.4 on
Page 23.
The chemical protective suit is equipped with exchangeable
gloves:
inside chemical-resistant FKM/butyl glove, outside optional

cut-resistant and watertight Tricotril overglove or optional
cut-resistant K-MEX-Gigant overglove
inside chemical-resistant laminate glove, outside cut and

Dräger
watertight Tricotril glove (glove combination)
inside chemical-resistant laminate glove, over it watertight

butyl glove (glove combination), outside cut-resistant
K-MEX-Gigant overglove
The chemical protective suit can be equipped either with socks
made from the same material as the suit or with boots. The
socks by themselves do not provide adequate protection from
mechanical stresses. The user must therefore also wear
suitable protective boots, which are approved in accordance
with EN ISO 20345. To facilitate stepping into the boots,
oversocks can be used. A cuff prevents the penetration of
substances between the socks and safety boots.
The visor is provided with a scratch proof screen on the outside
of the suit.
The chemical protective suit features a pocket for radio units
and a push-to-talk button flap. The pocket is labelled with the
type ID.
The following optional components can be fitted to the
chemical protective suit:
Regulating valve PT 120 L or Air-Connect:

Ventilation unit for the connection of external air supply
sources to the cooling system inside the suit.
D-Connect:

Bracket for additional equipment (e.g. thermal imaging
camera, measuring devices, rescue loops), which can be
fastenend on the left or on the right hip.
Fall-Connect:

Attachment for equipment for fall protection of persons. If a
fall connection is used, no external air supply may be
connected via an air venting hose.
Crotch strap:

for adjusting the length of the suit
Antifog visor in the suit:

prevents the visor from fogging.
Manometer bracket below the visor:

for fastening the manometer of the compressed air
breathing apparatus in the field of vision of the protective
® ®
, PSS
suit wearer
Task force ID numbers:

for easy recognition of the task force team.
A mark with a waterproof pen is possible, but not
recommended.
Dräger CPS 7900