Yamaha 01V Manual De Instrucciones página 291

1.3 ACTIVE SENSING (Fe)
Reception
Once this message has been received, an interval of 300ms or more
during which no message is received will cause MIDI communica-
tions to be initialized, clearing Running Status etc.
STATUS 11111110 FE
2. TRANSMISSION CONDITION
CTL Tx ON
CONTROL CHANGE $BnH
PGM Tx ON
PROGRAM CHANGE $CnH
PARAM Tx ON
SYSTEM EXCLUSIVE
PARAMETER CHANGE
$F0H, $43H, $1nH
(RESPONSE FOR
PARAMETER REQUEST)
SYSTEM EXCLUSIVE
BULK DUMP $F0H, $43H, $0nH
BULK REQUEST $F0H, $43H, $2nH
USER DEFINE
MMC $F0H, $7FH, nnH, 06H
MIDI IN
3. RECEIVE CONDITION
MIDI Rx CH?
CTL Rx ON
PGM OMNI ON
PGM Rx ON
CTL OMNI ON
PARAM Rx ON
PARAM OMNI ON
MIDI IN
BULK Rx ON
CTL ECHO ON
PGM ECHO ON
PARAM ECHO ON
Active Sensing
MIDI TX CH?
MIDI OUT
CTL ECHO ON
PGM ECHO ON
PARAM ECHO ON
$8nH NOTE OFF
$9nH NOTE ON/OFF
$BnH CONTROL CHANGE
$CnH PROGRAM CHANGE
SYSTEM EXCLUSIVE
$F0H, $43H, $1nH
PARAMETER CHANGE
$F0H, $43H, $3nH
PARAMETER REQUEST
SYSTEM EXCLUSIVE
$F0H, $43H, $0nH, BULK DUMP
$F0H, $43H, $2nH, BULK REQUEST
MIDI OUT
MIDI Data Format
4. PARAMETER CHANGE
BASIC FORMAT
STATUS 11110000 F0
ID No. 01000011 43
SUB STATUS 0pppnnnn pn
GROUP ID 00111110 3e
MODEL ID 00000100 04
PARAM TYPE 0ttttttt tt
DATA 0ddddddd dd0
:
0ddddddd ddn
EOX 11110111 F7
type
-----------------------------------------------------------------------------
0x00 edit buffer ...byte operation format
0x01 system memory (setup, backup) ...byte operation format
0x02 function call (mem/lib recall, mem/lib store, clear, title)
0x03 controller (LCD/fader mode)...byte operation format
0x04 multiple link (fader mode, solo mode, title,,,)
0x05 remote meter (meter data)
0x10 edit buffer ...7bit operation format
0x40 edit buffer ...bit operation format
0x41 system memory (setup, backup) ...bit operation format
0x43 controller (key remote) ...bit operation format
PARAMETER CHANGE (byte operation for type
0x00:edit buffer)
Reception
This message is received if [Parameter Change RX] is ON and the [Rx
CH] matches the Device Channel included in the SUB STATUS.
If [Parameter Change ECHO] is ON, this will be echoed.
The specified parameter will be controlled when this message is
received.
Transmission
If [Parameter Change TX] is ON, this message will be transmitted on
the [Tx CH] Device Channel when a parameter that is not specified
in the [Control Assign Table] is modified.
STATUS 11110000 F0
ID No. 01000011 43
SUB STATUS 0001nnnn 1n
GROUOP ID 00111110 3e
MODEL ID 00000100 04
PARAM TYPE 00000000 00
DATA 0aaaaaaa dd1
0aaaaaaa dd2
0000dddd dd3
0000dddd dd4
: :
EOX 11110111 F7
The valid range of addresses is 0x0000 - 0x03FF
293
System Exclusive Message
Manufacturer's ID No.(YAMAHA)
p=mode 1:parameter change or response
for request, 3:parameter request
n=0-15(Device Channel No.1-16)
MODEL ID (digital mixer)
Device code (01V)
(type)
data 0
:
data n
End Of Exclusive
System Exclusive Message
Manufacturer's ID No.(YAMAHA)
parameter change or response
n=0-15(Device Channel No.1-16)
MODEL ID
Device code (01V)
byte operation for edit buffer (type)
address( H) high 7 bits of 14 bits address
address( L) low 7 bits of 14 bits address
data( H) high 4 bits of 8 bits data
data( L) low 4 bits of 8 bits data
: continuous address datas
End Of Exclusive
01V—Manual de Instrucciones