Idiomas disponibles
Idiomas disponibles
8.1.1
Fitting the saw blade (Fig. 3)
Note:
Ensure that the right saw blade for the material in ques-
tion is always used.
Note:
Ensure that the chuck is free of splinters or other mate-
rial residues.
1. Turn the clamping lever (12) as far to the right as
possible and hold it in this position.
2. Insert the saw blade (14) into the chuck (11). When
inserting the saw blade (14), ensure that the back of
the saw blade is in the groove of the guide roller (9).
Ensure that the saw blade (14) is secured correctly
and that the teeth point in the direction of cutting.
3. Release the clamping lever (12).
Note:
Pull lightly on the saw blade to check that it does not
fall out during operation.
8.1.2
Removing the saw blade
1. Hold the saw blade (14) firmly.
2. Turn the clamping lever (12) as far to the right as
possible and hold it in this position.
3. Take the saw blade (14) out of the chuck (11).
4. Release the clamping lever (12).
8.2
Inserting/removing the battery
(16) in the battery mount (4) (Fig.
2)
Inserting the battery
1. Push the battery (16) into the battery mount (4). The
battery (16) clicks into place audibly.
Removing the battery
1. Press the unlock button (17) of the battery (16) and
remove it from the battery mount (4).
8.3
Test run
Note:
Before the first work and after each tool attachment
change, carry out a test run without load. Switch off the
product immediately if the tool attachment runs out of
round, there is considerable vibration or abnormal nois-
es are heard.
1. Before operation, check that the insert tool is cor-
rectly fitted, i.e. centred in the chuck (11).
9
Operation
The cordless rechargeable battery jigsaw has a pendu-
lum lifting device and a working light. The latches for
mitre angles enable precise working. Please refer to the
following descriptions for the function of the controls.
26 | GB
WARNING
Danger of injury!
Remove the battery from the power tool before carry-
ing out any work on the power tool (e.g. maintenance,
tool change, etc.) and when transporting and storing
it. There is a risk of injury if the on/off switch is oper-
ated unintentionally.
ATTENTION
Make sure that the ambient temperature does not ex-
ceed 50°C and does not fall below -20°C during work.
ATTENTION
The product is part of the 20V gomag series and may
only be operated with batteries of this series. Batter-
ies may only be charged with battery chargers of this
series. Observe the manufacturer's instructions.
Note:
Ensure that the right saw blade for the material in ques-
tion is always used.
9.1
On/Off switch (2) (Fig. 1)
Note:
The speed can be steplessly controlled by the on/off
switch. The further you press the on/off switch, the
higher the speed.
Note:
The appropriate speed may depend on the type and
thickness of the workpiece. The general rule is that the
workpieces can be cut faster at higher speeds, but the
service life of the saw blade is shorter.
1. To start the product, hold down the safety switch (1)
and press the on/off switch (2).
2. Release the safety switch (1) again.
3. To switch it off, simply release the on/off switch (2).
9.1.1
This product is equipped with an LED work lamp to illu-
minate the immediate work area and improve visibility
in poorly lit environments.
CAUTION
Do not look directly into the LED work lamp or the
light source.
1. The LED work lamp (13) lights up automatically as
soon as the product is switched on.
9.2
Setting the mitre angle (Fig. 4)
1. Loosen the Allen screws (7) with the Allen key (15).
2. Pull the base plate (6) back slightly.
www.scheppach.com
LED work lamp (13) (Fig. 1)
