Idiomas disponibles
Idiomas disponibles
GB
2. Checking the working depth:
■
Start the appliance (see chapter 6.6 "Starting
and stopping the motor (16, 17)", page 28).
■
Drive a short distance on the lawn and
check the result. If the lawn is insuffi-
ciently or irregularly scarified, the blade
system must be lowered.
3. Stop the appliance and wait until the blade
system has come to a standstill.
4. Turn the setting wheel (12/1) slightly to the
left to scarify more deeply (12/3). The blade
system is lowered.
5. Repeat the previous steps until the lawn is
scarified uniformly.
6.5
Making the mains connection (13, 14, 15)
1. Firmly plug the socket (13/1, 14/1) of the
mains cable into the plug (13/2, 14/2) on the
motor switch.
2. Clamp the mains cable (13/3, 14/3) into the
cable strain relief hook (13/4, 14/4) (15/a)
and (15/b) in such a way that it cannot be
pulled off the motor switch.
6.6
Starting and stopping the motor (16, 17)
IMPORTANT! Risk of damage to the appli-
ance. The motor and blade system can be dam-
aged by repeatedly switching on and off.
■
Switch the motor on only when the blade sys-
tem is at a standstill.
Starting the motor 32.4 E
1. Press the safety button (16/1) and hold (16/a).
2. Pull motor switch lever (16/2) towards the
handlebar (16/3) (16/b). Start the motor and
blade system.
3. Release the safety button (16/1) and hold the
motor switch lever (16/2).
NOTE The motor switch lever does not
latch. Hold it tight against the handlebar during
the entire working period.
Starting the motor 38.4 E
1. Press the safety button (17/1) and hold (17/a).
2. Pull the operator presence control (17/2) to-
wards the handlebar (17/3) (17/b). Start the
motor and blade system.
3. Release the safety button (17/1) and hold the
motor switch lever (17/2).
NOTE The operator presence control does
not latch. Hold it tight against the handlebar
during the entire working period.
28
Stopping the motor 32.4 E
1. Release the motor switch lever (16/2). It au-
tomatically returns to its initial position.
The motor stops immediately. The blade system
runs down to a standstill.
Stopping the motor 38.4 E
1. Release the operator presence control (17/2).
It automatically returns to its initial position.
The motor stops immediately. The blade system
runs down to a standstill.
CAUTION! Danger of cutting injuries.
There is danger of lacerations when reaching into
the blade system while it is running on or the
stopped blade system.
■
Stop the appliance and wait until the blade
system has stopped.
■
Disconnect the mains plug to power down the
appliance.
■
Wear protective gloves.
7 MAINTENANCE AND CARE
CAUTION! Danger of cutting injuries.
There is danger of lacerations when reaching into
the blade system while it is running on or the
stopped blade system.
■
Stop the appliance and wait until the blade
system has stopped.
■
Disconnect the mains plug to power down the
appliance.
■
Wear protective gloves.
NOTE Replace the defective mains cable
only with an original mains cable (with plug and
socket) from the manufacturer!
7.1
Cleaning the blade system
IMPORTANT! Danger from water. Water in
the appliance causes short-circuits and destroys
electrical components.
■
Do not spray the appliance with water.
■
Only use a broom or a brush for cleaning.
1. Stop the appliance and wait until the blade
system has come to a standstill.
2. Disconnect the mains plug.
3. Remove the grass collector (see chapter 6.3
"Attaching and removing the grass collector
[optional] (11)", page 27).
4. Tilt the appliance onto the side and clean the
blade system with a broom or handbrush.
32.4 E Basic Care | 38.4 E Combi Care
Maintenance and care
