Idiomas disponibles
Idiomas disponibles
9.1.1
LED work lamp (4) (Fig. 1)
This product is equipped with an LED work lamp to illumi-
nate the immediate work area and improve visibility in
poorly lit environments.
CAUTION
Do not look directly into the LED work lamp or the light
source.
1. The LED work lamp (4) lights up automatically as
soon as the product is switched on.
9.2
Adjusting the speed
1. Light pressure on the on/off switch (6) results in a low
speed. As the pressure increases, the speed increas-
es.
We recommend determining the speed using practical
tests.
Note:
The integrated motor brake ensures a quick standstill.
9.3
Guide the reciprocating saw safely
The foot plate can be swivelled to adapt to the workpiece
and for secure support. It must always be in contact with
the workpiece when the product is in operation.
10 Working instructions
• Check the material to be processed for foreign objects
such as nails, screws etc. and remove them.
• Ensure that the ventilation slots are not covered.
• Switch on the product and only then approach the ma-
terial to be processed.
• Switch the product off immediately if the saw blade
jams. Spread the already sawn gap with a suitable
tool and pull out the product.
• Adjust the saw blade and stroke rate to suit the mate-
rial to be processed.
• Saw blades optimised for each application of your
product are commercially available in different
lengths.
• Saw the material with a steady feed.
• Do not attempt to saw extremely small workpieces.
• Do not tilt too far forward. Always ensure a secure
footing, especially on scaffolding and ladders.
10.1
Test run
Note:
Before the first work and after each tool attachment
change, carry out a test run without load. Switch off the
product immediately if the tool attachment runs out of
round, there is considerable vibration or abnormal noises
are heard.
10.2
Plunge saw (Fig. 6)
CAUTION
Risk of kick-back!
Plunge cuts may only be made in soft materials (wood
or similar).
20 | GB
• Use only saw blades that are suitable for plunge cuts.
Proceed as follows:
1. Place the reciprocating saw with the lower edge of the
foot plate (2) on the workpiece. Switch the product on.
2. Tilt the reciprocating saw forwards and plunge into the
workpiece with the saw blade (1).
3. Set the reciprocating saw vertically and continue saw-
ing along the cut line.
10.3
Information on saw blades
You can use any saw blade, provided it is furnished with
the appropriate mount - ½" (12.7 mm) universal shank.
Optimised saw blades in various lengths are commercially
available for every application of your reciprocating saw.
Note:
TPI = teeth per inch = the number of teeth per 2.54 cm
11 Cleaning and maintenance
WARNING
Have maintenance and repair tasks that are
not described in this operating manual, car-
ried out by a specialist workshop. Use only
original spare parts.
There is a risk of accident! Always perform
maintenance and cleaning work with the bat-
tery removed. There is a danger of injury! Let
the Product cool down before all mainte-
nance and cleaning tasks. Elements of the
engine are hot. There is a danger of injury
and burning!
The product can start unexpectedly and cause injuries.
–
Remove the battery.
–
Allow the product to cool down.
–
Remove the tool attachment.
11.1
Cleaning
1. Keep protective devices, air vents and the motor
housing as free of dust and dirt as possible. Rub the
product clean with a clean cloth or blow it off with
compressed air at low pressure. We recommend that
you clean the product directly after every use.
2. Ventilation openings must always be free.
3. Do not use any cleaning products or solvents; they
could attack the plastic parts of the product. Make
sure that no water can penetrate the product interior.
4. Always keep the product clean, dry and free from oil
or grease. Remove dust after each use and before
storage.
5. If necessary, clean the saw blade holder with a brush
or by blowing it out with compressed air.
6. Wipe any dirt off the lens with a dry cloth. Be careful
to avoid scratching the LED lamp as this can severely
reduce the light intensity.
www.scheppach.com
