Genie Directlift 2060 Manual De Funcionamiento Y Mantenimiento página 11

2060-3060 eng.qxd 11/9/05 11:02 AM Page 11
'\ 1./
........ _:]:7 .......
}"E
NOTE
Each Remote Control must be programmed
separately.
• The Remote Controls will not cause the door
Opener to close the garage door if the Safe-T-
Beam® System is malfunctioning.
• When programming the Remote Controls, they
must be at least 24" from the Antenna Wire.
• If the red Learn Indicator Light blinks
approximately 4 times per second,
programming has stopped. If programming
has stopped, repeat the above steps.
• Each Button on a 2 or 3 Button Remote Control
is for a different Opener. You cannot use more
than one Button per Remote, per Opener.
• A maximum of seven Remote Controls or
Wireless Keypads can be stored into the
Receiver at one time. If a Remote Control
becomes lost, or if you want to delete a Remote
Control or Wireless Keypad, see "To Erase All
Receiver Memory."
A To program one Button of a Remote Control (Figure 12):
• Locate Learn Button and Learn Indicator Light near
Terminal Strip on Power Head (Figure 13).
• Press and release Learn Button. Red Learn Indicator
Light will blink 2 times per second.
• Press Remote Control Button once within 30
seconds. Red Learn Indicator Light will stay lit.
• Press Remote Control Button again. Red Learn
Indicator Light will go out, indicating that
memory is stored.
B Program each additional Remote using step A above
(up to seven).
7b
A
E%ase All
_es_etes f_os_ Pewe_ Mead _{e_"_'_e_y
Press and hold Learn Button on Power Head for 10
seconds or until Learn Indicator Light goes out.
Memory is erased:
• Program Transmitter/Receiver again as needed.
To _eplace _Res_ete Co_d_'ol Ba e_y'
A FOR NON-FLASHLIGHTMODELS
• Pop off the back of the transmitter.
- Use coin, pen, screwdriver or any similar device.
- Replace old Battery with new coin type battery.
• Replace back of remote.
B FOR FLASHLIGHT MODELS
• Slide open battery cover.
- Replace old Battery with new AAA battery.
• Replace battery cover.
WARNING
A moving garage door may cause serious injury or death.
• Keep people clear of opening while door is moving.
• Do not allow children to play with the Remote Controls.
If the Safety Reversedoes not work properly:
• Close the door and disconnect the Opener using the
Emergency ReleaseCord.
• Do not use the door Opener, Remote Controls, or
Wireless Keypad.
• Refer to the door and door Opener Owner's Manuals
before attempting any repairs.
[Ies_ote Co_ _01 Opera io_
A Press Button on Remote Control. Garage door will move.
B Press Button again. Garage door will stop:
• The door automatically stops at the end of the open or
close cycle.
C Press Button again. Garage door will reverse.
315 Mhz _-f_-_'-_ _ 315 Mhz
Frequency _I Frequency
__ Switch _ Switch
390 Mhz
1 Button Compact Remote 3 Button Compact Remote
w/Docking Station w/Docking Station
Figure 12 Genie Remote Controls
Receiver Learn
Code Button
Receiver
,2 S_ i
Figure 13 Learn Code Button and Indicator Light
D Some Remote Controls are equipped with a flashlight.The
logo is the button which operates the light. There is a
backlight under the button.When it does not light, it
indicates the battery needs replaced.
Frequency
Flashlight Button Switch
J
\\ /'
1 Button Remote 3 Button Remote 3 Button Large
w/Flashlight w/Flashlight Remote
w/Flashlight
Figure 14 Genie Remote Controls
11
........ \::7 ...
,f] "_
......................... L_: N ........................