DeWalt DCMWP134 Manual página 64

EnGLIsh

DANGER: To reduce the risk of serious personal injury, turn unit off and remove the safety key and battery packs before
making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury.
For assistance with your product call your local D
PROBLEM
Mower doesn't run when bail
handle is activated
Blade motor stops while mowing
The single touch handle 1 will not
lock into the storage position
Self drive motor stops
while working
Mower runs but cutting
performance is unsatisfactory, or
does not cut entire lawn
Mower is too hard to push
Mower is abnormally noisy
and vibrates
Mower not picking up clippings
with bag
62 62
TROUBLESHOOTING GUIDE
WALT authorized service centre.
e
SOLUTION
Check to make sure safety key has been installed and is fully seated and that power button has been pressed.
Release bail handle. Turn mower off. Remove safety key and battery packs. Turn mower over and check that the blades turn freely.
Check that the battery port is free of debris and is connected properly.
Have the batteries been fully charged? Press state of charge button.
If the handle folding indicator 15
Release bail handle. Turn mower off. Remove safety key and battery packs. Turn mower over and check that the blades turn freely.
Raise cutting height of wheels to highest position and start mower.
Check that the battery port is free of debris.
Have the batteries been fully charged? Press state of charge button.
Avoid overloading the mower. Slow down the cutting pace, or raise the cut height.
If the overheat indicator is illuminated allow the batteries and mower to cool down. When cooled, restart the mower and
13
resume cutting with the mower deck set higher.
Ensure the two storage latches 30
touch handle 1 into the stoarge position.
The main handle 4 must fully engage the handle windows
handle 4 towards the handle support
as shown in Fig. H.
Shut down power to the self driving mower.
Clean the self drive motor housing of debris.
Check that the wheels are spinning freely.
Have the batteries been fully charged? Press state of charge button.
Release bail handle to turn mower off. Remove safety key and battery packs. Turn mower over and check:
• Blades for sharpness ‑ Keep blades sharp.
• Deck and discharge chute for clogging.
Wheel height adjustment may be set too low for grass condition. Raise cutting height.
The blade sharpening indicator 16
Blade Sharpening section in this manual.
Release bail handle to turn mower off. Remove safety key and battery packs. Raise cutting height to reduce deck drag on grass.
Check each wheel for free rotation.
If the overheat indicator 13 is illuminated allow the batteries and mower to cool down. When cooled, restart the mower and
resume cutting with the mower deck set higher.
Release bail handle to turn mower off. Remove safety key and battery packs. Turn mower on side and check blade to ensure it
has not been bent or damaged. If blade is damaged, replace with a D
is damaged, return mower to a D
E
If there is no visible damage to the blade and the mower still vibrates: Release bail handle to turn mower off. Remove safety
key and battery packs. Disassemble entire blade assembly as described in the Removing and Installing Blades section.
Remove any debris and clean each piece. Replace each piece as described in the Removing and Installing Blades section. If
mower still vibrates, return the mower to an authorized D
Chute clogged. Release bail handle to turn mower off. Remove safety key and battery packs. Clear chute of grass clippings.
Raise cutting height of wheels to shorten length of the cut.
Bag full. Empty bag more often.
is illuminated refer to the Raise the Single Touch Handle section in this manual.
at the bottom of the single touch handle
29 . If they are not engaged as shown in Fig. G, press the main
2 until two audible clicks are heard and both sides of handle windows
will illuminate when the blades need service. Sharpen or replace the blades, refer to the
WALT Authorized service centre.
WALT service centre.
E
1 tubes pop outward before lowering the single
WALT replacement blade. If the underside of the deck
E
29 are closed