Idiomas disponibles
Idiomas disponibles
WARNING: Mow across the face of slopes, never
up-and-down. Exercise extreme caution when changing
direction on slopes. Do not mow excessively steep slopes
(greater than 15 degrees). Always maintain good footing.
•
Release bail handle
8
to turn mower "OFF" when crossing
any gravel area (stones can be thrown by the blades).
•
Set mower at highest cutting height when mowing in rough
ground or in tall weeds. Removing too much grass at one
time can cause the motor to be overloaded and to stop.
•
If a grass collection bag
season, the grass may tend to clog up at the discharge
opening. Release bail handle to turn mower off, remove
the safety key
6
and battery packs
collection bag
22
and shake the grass down to the back
end of the bag. Also clean out any grass or debris which may
be packed around the discharge opening. Reinstall the grass
collection bag
.
22
•
If mower should start to vibrate abnormally, release bail
handle to turn mower off, remove the safety key and battery
packs. Immediately check for cause. Vibration is a warning
of trouble. Do not operate the mower until a service check
has been made.
•
For best cutting results, keep blades sharpened
and balanced.
•
Inspect and thoroughly clean mower after each use. A deck
with caked grass will degrade performance.
•
Always release the bail handle to turn mower off, remove
safety key and battery packs when leaving it unattended
even for a short period of time.
The following suggestions will help you to obtain
optimum runtime from your cordless mower:
•
Slow down your cutting pace in areas where the grass is
especially long or thick.
•
Avoid mowing when the grass is wet from rain or
dew-soaked.
•
Cut your lawn frequently, especially during high
growth periods.
nOTE: It is recommended that both of your battery packs be
recharged after each use to prolong the battery life. Frequent
charging will not harm your battery packs, and will ensure that the
battery packs are fully charged and ready for their next use.
nOTE: Storing the battery packs not fully charged will
shorten their life.
MAINTENANCE
This product has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper care and regular cleaning.
DANGER: To reduce the risk of serious personal
injury, turn unit off and remove the safety key and
battery pack before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.
The charger and battery pack are not serviceable.
22
is used during the fast growing
26
. Remove the grass
Optional Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
MAINTENANCE
DANGER: To reduce the risk of serious personal
injury, turn unit off and remove the safety key and
battery packs before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.
Removing and Installing Blades (Fig. X–DD)
DANGER: RISK OF INJURY. WHEN REASSEMBLING THE
BLADE SYSTEM, ENSURE EACH PART IS REINSTALLED
CORRECTLY, AS DESCRIBED BELOW. IMPROPER ASSEMBLY
OF THE BLADES OR OTHER PARTS OF THE BLADE SYSTEM
MAY CAUSE SERIOUS INJURY.
DANGER: To reduce the risk of serious personal
injury, turn unit off, remove safety key and battery
packs before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Replacement blades are available from your
nearest authorized service center. This mower requires
replacement blades: DT20902.
Cut a piece of 38 mm x 89 mm timber
to keep blades from turning when removing the blade
assembly bolt
43
.
WARNING: Use gloves and proper eye protection. Turn the
mower on its side. Be careful of sharp edges of blades.
1. Position the mower on its side, with two wheels flat
on the ground.
2. Position the 38 mm x 89 mm timber
assembly
47
and outer lip of deck as shown in Fig. X to
keep the blades from turning.
3. Unscrew and remove the blade assembly bolt
counterclockwise with a 14 mm (9/16") wrench
included) as shown in Fig. X, Y.
4. Remove the keyed spacer
the blade shaft
49
.
5. Secure the blade assembly
6. Unscrew the four blade nuts
with a 14 mm (9/16") wrench
shown in Fig. Z. First unscrew the two blade nuts
blade 1
53
and remove blade 1. Then unscrew the two
blade nuts
for blade 2
51
blade hub
.
48
nOTE: The mower blades
mounting holes
55
permitting them to only be installed
onto the blade hub
48
7. Examine all pieces for damage and replace if necessary.
WALT-recommended
e
42
(about 61 cm long)
42
between the blade
43
44
and blade assembly
45
47
in a vise
34
as shown in Fig. Z.
counterclockwise
51
44
(not included) as
51
and pull blade 2 from the
52
53
and
52
have keyed
in the correct orientation.
EnGLIsh
(not
from
47
for
59
59
