Idiomas disponibles
Idiomas disponibles
EnGLIsH
Fuel Gauge Battery Packs (Fig. B)
Some D
WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button.
A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Attaching Side Handle (Fig. C)
WARNING: Before using the tool, check that the handle is
tightened securely.
Screw the side handle adapter
either side of the gear case, then screw the side handle
the adapter. The adapter MUsT be used together with the
side handle. If the adapter is missing, stop using the tool, find a
nearest D
WALT service centre for a new adaptor.
e
The side handle should always be used to maintain control of
the tool at all times.
Rotating the Gear Case (Fig. A)
To improve user comfort, the gear case will rotate 90° for
cutting operations.
1. Remove the four corner screws attaching the gear case to
motor housing.
2. Without separating the gear case from motor housing,
rotate the gear case head to desired position.
nOTE: If the gear case and motor housing become separated
by more than 3.17 mm, the tool must be serviced and
re-assembled by a D
WALT service centre. Failure to have the
e
tool serviced may motor and bearing failure.
3. Reinstall screws to attach the gear case to the motor
housing. Tighten screws to 12.5 in.-lbs. torque.
Overtightening could cause screws to strip.
Guards
CAUTION: Guards must be used with all grinding
wheels, cutting wheels, sanding flap discs, wire
brushes, and wire wheels. The tool may be used
without a guard only when sanding with conventional
sanding discs. Refer to Figure A to see guards provided
with the unit. Some applications may require purchasing
the correct guard from your local dealer or authorized
service centre.
nOTE: Edge grinding and cutting can be performed with Type
27 wheels designed and specified for this purpose; 6.35 mm
thick wheels are designed for surface grinding while thinner
Type 27 wheels need to be examined for the manufacturer's
label to see if they can be used for surface grinding or only
edge grinding/cutting. A Type 1 guard must be used for any
wheel where surface grinding is forbidden. Cutting can also be
performed by using a Type 41 wheel and a Type 1 guard.
48
into one of the holes on
12
11
into
nOTE: See the Accessory Chart to select the proper guard /
accessory combination.
Adjusting and Mounting Guard (Fig. D)
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
adjustment Options
For guard adjustment, the guard release lever
one of the alignment holes
16
ratcheting feature.
Mounting Guard (Fig. D)
CAUTION: Prior to mounting guard, ensure the screw,
lever, and spring are fitted correctly before mounting
the guard.
1. With the spindle facing the operator, align the guard parallel
to the mounting slot
14
in gearcase.
2. Slide the guard into the mounting slot with the guard
tabs
riding along the 2 flat sides of the collar just above
15
the mounting slot.
3. Press and hold the guard release lever
the guard around until the lever engages one of the
alignment holes
.
16
4. Release the guard release lever.
5. To position the guard:
Press and hold the guard release lever
guard clockwise or anti-clockwise into the desired
working position.
nOTE: The guard body should be positioned between
the spindle and the operator to provide maximum
operator protection.
The guard release lever should snap into one of the
alignment holes
16
on the guard collar. This ensures that
the guard is secure.
6. To remove the guard, follow steps 1–3 of these instructions
in reverse.
Flanges and Wheels
Mounting Non-Hubbed Wheels (Fig. E)
WARNING: Failure to properly seat the flanges and/or
wheel could result in serious injury (or damage to the tool
or wheel).
CAUTION: Included flanges must be used with depressed
centre Type 27 and Type 42 grinding wheels and
Type 41 cutting wheels. See the accessory chart for
more information.
WARNING: A closed, two-sided cutting wheel guard is
re quired when using cutting wheels.
WARNING: Use of a damaged flange or guard or fail ure
to use proper flange and guard can re sult in injury due to
wheel breakage and wheel contact. See the accessory
chart for more information.
8
engages
on the guard collar using a
8
and rotate
. Rotate the
8
