Idiomas disponibles
Idiomas disponibles
NOTE: If the driver blade will not reset after rotating the stall release lever, manually
resetting the blade with a long screw driver may be necessary.
7. Rotate the magazine back into position under the nose of the tool and tighten hex bolts.
8. Reinsert battery pack.
NOTE: The tool will disable itself and not reset until the battery pack has been removed
and reinserted.
9. Reinsert nails into magazine (refer to Loading the Tool).
10. Release the pusher latch.
11. Disengage the trigger lock-off when ready to continue nailing.
NOTE: Should nails jam frequently or the driver blade continually fail to reset, have tool
serviced by an authorized D
WALT service center.
E
Cold Weather Operation
When operating tools at temperatures below freezing:
1. Keep tool as warm as possible prior to use.
2. Actuate the tool 10 or 15 times into scrap lumber before using.
Hot Weather Operation
Tool should operate normally. However, keep tool out of direct sunlight as excessive heat can
deteriorate bumpers and other rubber parts resulting in increased maintenance.
Rotating Rafter Hook (Fig. 13)
WARNING: Remove nails from magazine before making any
adjustments or servicing this tool. Failure to do so may result in
serious injury.
CAUTION: When not in use, place tool on its side on a
stable surface where it will not cause a tripping or falling
hazard.
CAUTION: Some tools with large battery packs will stand
upright on the battery pack but may be easily knocked over.
The D
WALT cordless nailer includes a rotating rafter hook (J) and
E
can be easily positioned to the left or right of the tool to accommodate left- or right-handed
users.
If use of the hook is not desired at all, it can be rotated to the front or back of the handle base.
MAINTENANCE
WARNING: To reduce the risk of serious personal injury, disconnect battery pack
from tool before making any adjustments, changing accessories, servicing, or
moving the tool. Such preventative safety measures reduce the risk of starting the tool
accidentally.
Daily Maintenance Chart
ACTION Clean magazine, pusher, and contact trip mechanism.
WHY
Permits smooth operation of magazine, reduces wear, and prevents jams.
HOW
Blowing off the tool with compressed air is the most effective way to clean the tool.
The use of oils, lubricants periodically or solvents is not recommended as they tend to
attract debris and/or damage the plastic parts of the tool.
ACTION Before each use, check to ensure all screws and fasteners are tight and undamaged.
WHY
Prevents jams and premature failure of tool parts.
HOW
Tighten loose screws using the appropriate hex wrench or screwdriver.
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when
performing this.
NOTICE: When cleaning, use only a damp cloth on plastic parts. Many household cleaners
contain chemicals which could seriously damage plastic parts. Also, do not use gasoline,
turpentine, lacquer or paint thinner, dry cleaning fluids or similar products which may seriously
damage plastic parts. Never let any liquid get inside the tool; never immerse any part of the
tool into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt
and grease may be removed from the exterior of the charger using a cloth or soft non-metallic
brush. Do not use water or any cleaning solutions.
Lubrication
NOTICE: NEVER spray or in any other way apply lubricants or cleaning
solvents inside the tool. This can seriously affect the life and performance
of the tool.
D
WALT tools are properly lubricated at the factory and are ready for use.
E
However, it is recommended that, once a year, you take or send the tool to
a certified service center for a thorough cleaning and inspection.
FIG. 13
Accessories
WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only D
Recommended accessories for use with your tool are available at extra cost from your local
dealer or authorized service center. If you need assistance in locating any accessory, please
J
contact D
WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call
E
1-800-4-D
WALT (1-800-433-9258) or visit our website www.D
E
Repairs
The charger and battery pack are not serviceable.
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should
be performed by a D
or other qualified service personnel. Always use identical replacement parts. Refer to the
Troubleshooting Guide at the end of this section.
Register Online
Thank you for your purchase. Register your product now fo+r:
• WARRANTY SERVICE: Registering your product will help you obtain more efficient
warranty service in case there is a problem with your product.
• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or
theft, your registration of ownership will serve as your proof of purchase.
• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely
event a safety notification is required under the Federal Consumer Safety Act.
Register online at www.D
10
WALT, recommended accessories should be used with this product.
E
WALT factory service center, a D
WALT authorized service center
E
E
WALT.com/register.
E
WALT, have not been tested
E
WALT.com.
E
