Idiomas disponibles
Idiomas disponibles
B. M2-CEILING-WALL-KT
1.
Make sure the power is disconnected to the conduit system before
installing the luminaire.
2.
Mark and drill holes for fastening end brackets. Use two (2) 1/4" diameter
fasteners (customer supplied) at center to center measurements (see
Figure 2). It is recommended that stainless steel hardware be used in
locations with corrosion concerns.
3.
Luminaire is now ready for mounting. It is strongly suggested to use
two (2) qualified tradespeople to proceed with the final mounting of the
luminaire. This is recommended to avoid any personal injury or damage to
the luminaire.
4.
For end mount wall/ceiling mounting brackets, it is recommended to
mount one bracket first and then, while supporting the luminaire, insert it
into the mounted bracket, then attach the other bracket.
Do not let the luminaire hang or flex on one bracket at a time. Failing to
comply will result in breakage of bracket and possible injury or death.
8
5.
Aim the luminaire to achieve desired light output and tighten the 1/4" set
NOTES:
1.
screws on brackets. Torque to 64 in.-lbs. (7 .2 N-m).
6.
Use set screw to limit rotation of the luminaire.
D
2 Foot
2 Foot
Length
(in)
(mm)
A
28.5
724
B
24.0
610
166.9
6.57
C
8
7
6
63.5
B
2.50
205.2
8.08
175.3
A
6.90
8
54
2.13
Figure 2. Ceiling-Wall Mount Installation
8
7
6
IF 1938 • 04/22
!
WARNING
7
6
4 Foot
4 Foot
(in)
(mm)
28.5
724
39.0
991
5
4
175.3
6.90
A
669.3
26.35
B
B
723
7
6
28.5
B
5
4
Copyright © 2022, Eaton's Crouse-Hinds Division
C. M2-CEILING-SWIVEL-KIT
1.
Make sure the power is disconnected to the conduit system before
installing the luminaire.
2.
Identify mounting location suitable for supporting luminaire, mark and drill
holes for fastening swivel brackets per center-to-center dimension 'A' in
table below (see Figure 3).
3.
Mount swivel bracket assemblies to luminaire driver housing as shown
in Figure 3. Use two (2) of the provided 1/4" hex bolts and split ring lock
washers for each bracket. Torque to 64 in-lb (7 .2 N-m).
4.
Luminaire is now ready for mounting. It is strongly suggested to use
two (2) qualified tradespeople to proceed with the final mounting of the
luminaire. This is recommended to avoid any personal injury or damage to
the luminaire.
5.
Install and tighten 1/4" diameter fasteners (customer supplied) in each
of the bracket mounting holes. It is recommended that stainless steel
hardware be used in locations with corrosion concerns.
Do not let the luminaire hang or flex on one bracket at a time. Failing to
5
4
3
comply will result in breakage of bracket and possible injury or death.
6.
Adjust the position of the luminaire to the desired angle and tighten the
two (2) 5/16" pivot bolts snugly to the bracket and then tighten hex nuts.
Torque to 120 in.-lbs. (13.6 N-m).
A
2 Foot
Length
A
B
3
2
B
8
NOTES:
1.
D
166.9
6.57
C
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
AND IS TO BE RETURNED UPON REQUEST.
MATERIAL:
Material
... THICK
Finish
FINISH:
CODE ...
ASSY2
ASSY1
NEXT ASSY.
APPLICATION
5
4
3
B
TOLERANCES
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
UNLESS OTHERWISE SPECIFIED,
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
UNLESS OTHERWISE SPECIFIED
ALL PRIMARY DIMENSIONS
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
in.
mm
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
ARE IN
INCHES.
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
.X
±
.1
±
.3
DIMENSIONS IN [ ] ARE IN
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
.XX
A
±
.01
±
.13
MILLIMETERS.
AND IS TO BE RETURNED UPON REQUEST.
.XXX
±
.005
±
.000
MATERIAL:
Material
ORIGINAL DATE
MM/DD/YYYY
ANGLES
±
1.5
±
1.5
... THICK
REDRAWN DATE
MM/DD/YYYY
DIM AND TOL IN ACCORDANCE
FINISH:
Finish
WITH ASME Y14.5 2009.
DRAWN BY
Your Name
CODE ...
THIRD ANGLE PROJECTION
CHECKED BY
Your Name
ASSY2
CAT2
APPROVED BY
Your Name
ASSY1
CAT1
Your name
APPROVED BY
NEXT ASSY.
USED ON
APPLICATION
3
2
8
!
WARNING
2
1
2 Foot
4 Foot
4 Foot
(in)
(mm)
(in)
(mm)
26.4
670
26.4
670
24.0
610
39.0
991
1
7
6
1/4-20 x 1/2" CAP SCREW
D
1/4" SPLIT LOCK WASHER
C
TOLERANCES
UNLESS OTHERWISE SPECIFIED,
UNLESS OTHERWISE SPECIFIED
ALL PRIMARY DIMENSIONS
in.
mm
ARE IN
INCHES.
.X
±
.1
±
.3
DIMENSIONS IN [ ] ARE IN
.XX
±
.01
±
.13
MILLIMETERS.
.XXX
±
.005
±
.000
Title Line 1
ORIGINAL DATE
MM/DD/YYYY
ANGLES
±
1.5
±
1.5
TITLE
MM/DD/YYYY
REDRAWN DATE
Title Line 2
DIM AND TOL IN ACCORDANCE
WITH ASME Y14.5 2009.
Your Name
DRAWN BY
FIRST MADE FOR Catalog Family
175.3
THIRD ANGLE PROJECTION
CHECKED BY
Your Name
CAT2
APPROVED BY
Your Name
SIZE
CODE IDENT. NO.
0000000
D
CAT1
6.90
Your name
APPROVED BY
USED ON
SCALE 1:2
WT. 15.84 LB
SHEET 3 OF 5
2
1
669.3
B
26.35
B
A
Figure 3. Ceiling-Swivel Mount Installation
Title Line 1
TITLE
Title Line 2
FIRST MADE FOR Catalog Family
SIZE
CODE IDENT. NO.
0000000
REV.
D
rev
SCALE 1:2
WT. 15.84 LB
SHEET 2 OF 5
1
7
6
D
C
5
4
B
A
A
B
REV.
rev
5
4
Page 2
3
THIS IS PROPERTY OF EATON AND CONTAI
TRADE SECRET INFORMATION. POSSESSIO
ANY RIGHTS TO LOAN, SELL OR DISCLOS
REPRODUCTION OR USE FOR ANY PURPO
IT WAS SUPPLIED MAY NOT BE MADE
WRITTEN PERMISSION OF EATON. THIS D
AND IS TO BE RETURNED UPON
Material
MATERIAL:
... THICK
FINISH:
Finish
CODE ...
ASSY2
ASSY1
NEXT ASSY.
APPLICATION
3
