Tabla de contenido
Idiomas disponibles
Idiomas disponibles
English
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
SPECIFICATIONS
Blade diameter
Arbor size
RPM
Lock‑Off Button (Fig. A)
Your cut‑off tool is equipped with a lock‑off button
To lock the trigger switch in the OFF postition, push the
lock‑off button from the left side of the tool. To unlock the
trigger switch, push the lock‑off button from the right side
of the tool.
Spindle Lock Button (Fig. A)
The spindle lock button
13
screw
11
when changing accessories.
1. To engage the spindle lock button, remove the battery
pack and make sure trigger switch is in the OFF position
and lock‑off button is engaged.
2. Depress the spindle lock button and turn the wheel and
spindle until the lock button engages the spindle.
3. Use supplied wrench
and remove or mount accessories. Spindle threads are
right hand.
Installing Abrasive and Diamond Wheels
(Fig. A, D)
WARNING: Install only one blade.
1. Lay unit on a firm surface, with the arbor screw
facing upward.
2. Using supplied 1/2" (13 mm) open end wrench
(located in the battery compartment), remove arbor
screw
11
, outer clamp washer
if one is installed. Hold arbor screw
spindle lock button
13
3. The inner clamp washer
double D shaft and retaining ring.
4. Slip wheel over spindle
Start threading on arbor screw which will self align outer
clamp washer.
iMPORTAnT: Make sure the diamond blade is installed
with the correct rotation, as marked on the blade rotation
indicator
12
.
5. Engage spindle lock button and tighten screw firmly with
wrench. Do not over‑tighten arbor screw.
6. Turn wheel by hand to ensure it is properly centered. The
wheel should not hit the shoe or guard. The screw and
flanges should be tight.
12
DCs692
9" (230 mm)
7/8" (22.2 mm)
6600
is used to lock the arbor
to unscrew the arbor screw
6
21
and used wheel
11
from turning with
. Spindle threads are right hand.
23
is held in place with a
25
. Slip on outer clamp washer.
CAUTION: Only use 9" (230 mm) Type 1/41 wheels
with 7/8" (22.2 mm) arbor hole with this tool. Never
force a wheel onto the machine or alter the size of the
arbor hole.
Replacing Worn Clamp Washers (Fig. D)
WARNING: Replace clamp washers as they wear. They
may become sharp with extended use.
1. Remove the arbor screw
and used wheel
Installing Abrasive and Diamond Wheels.
2. To remove the inner clamp washer
retaining ring that holds the inner clamp washer to the
double D shaft.
3. Remove the inner clamp washer and replace with a new
one. Orient the inner clamp washer with the depressed
.
3
center section toward the blade. Make sure the new
inner clamp washer is secure with the retaining ring
in place.
4. Install the wheel
arbor screw
Diamond Wheels.
Adjusting the Guard Angle (Fig. E)
WARNING: Do not use guard rotation handle to
hold tool while cutting. Guard rotation handle is
only used for adjustment of the guard while tool is not
in use.
CAUTION: Guard may be hot. Use guard handle to
rotate guard.
11
WARNING: Always make sure the guard is properly
engaged before starting the machine.
You can adjust the angle of the guard.
1. To adjust the angle of the guard, pull back the guard
rotation release lever
2. Grasp the guard
and rotate to desired angle.
3. Release the guard rotation release lever and make sure it
11
engages, locking the guard in place. If the guard rotation
release lever doesn't engage, rotate the guard slightly
6
until the guard rotation release lever returns to the
locked position.
22
D
WALT Bluetooth® Tool Tag Ready (Fig. A)
e
Optional Accessory
WARNING: Read instruction manual for the D
Bluetooth® Tool Tag.
WARNING: Remove battery from tool before installing
the D
WARNING: When installing or replacing the D
Bluetooth® Tool Tag, use only the screws provided. Be
sure to securely tighten the screws.
Your tool comes with mounting holes
for installing a D
will need a T15 torx bit tip to install the tag. Screw torque
should be between 0.8 and 1.2 Nm (7.1 to 10.6 in‑lbs). The
D
WALT Tool Tag is designed for tracking and locating
e
professional power tools, equipment, and machines using
, outer clamp washer
11
if one is installed as described in
22
22
, new outer clamp washer
11
as described in Installing Abrasive and
14
and hold it.
9
firmly by guard rotation handle
WALT Bluetooth® Tool Tag.
e
WALT Bluetooth® Tool Tag (DCE041). You
e
21
23
, first remove the
21
, and
10
WALT
e
WALT
e
15
and fasteners
27
Tabla de contenido
