Finishing Operation; Transport; Storage; Care And Service - Kärcher CS 400/36 Battery Manual De Instrucciones

b Set the cut on the tension side from the bottom.
 Trunk is supported on 1 side:
a For the relief cut on the pressure side, saw in
about 1/3 of the trunk diameter from below.
Illustration Y
b Set the cut on the tension side from the top.
Removing the battery pack
Note
During longer work breaks, remove the battery pack
from the device and secure it against unauthorised use.
1. Pull the battery pack unlocking button in the direc-
tion of the battery pack.
Illustration Z
2. Press the battery pack unlocking button to unlock
the battery pack.
3. Remove the battery pack from the device.

Finishing operation

1. Remove the battery pack from the device (see
Chapter Removing the battery pack).
2. Clean the device (see Chapter Cleaning the de-
vice).

Transport

CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transporta-
tion.
CAUTION
Uncontrolled startup
Incision injuries
Remove the battery pack from the device before trans-
port.
Transport the device only with the blade guard fitted.
1. Remove the battery pack (see chapter Removing
the battery pack).
2. Push the hand guard/chain brake lever towards the
guide rail.
Illustration N
The chain brake is locked.
3. Install the bar scabbard.
Illustration F
4. Only carry the device by the handle and with the
guide rail facing to the rear.
5. Empty the chain oil tank when transporting over
longer distances.
a Remove the chain oil tank cap.
Illustration G
b Fill the chain lubricating oil into a suitable contain-
er.
c Tighten the chain oil tank cap.
6. Secure the device against slipping and tipping over
when transporting in vehicles.

Storage

CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
CAUTION
Uncontrolled startup
Incision injuries
Remove the battery pack from the device before stor-
age.
Store the device only with the blade guard fitted.
26
1. Remove the battery pack (see chapter Removing
the battery pack).
2. Push the hand guard/chain brake lever towards the
guide rail.
Illustration N
The chain brake is locked.
3. Install the bar scabbard.
Illustration F
4. Empty the chain oil tank.
a Remove the chain oil tank cap.
Illustration G
b Fill the chain lubricating oil into a suitable contain-
er.
c Tighten the chain oil tank cap.
5. If the device is to be stored for more than one month,
oil the chain to prevent rust.
6. Store the device in a dry, well ventilated location.
Keep away from corrosive substances such as gar-
den chemicals and defrosting salt. Do not store the
device outdoors.

Care and service

CAUTION
Uncontrolled startup
Incision injuries
Remove the battery from the device before all work on
the device.
CAUTION
Sharp chain
Incision injuries
Wear protective gloves when working on the chain.
Cleaning the device
1. Remove the battery pack (see Chapter Removing
the battery pack).
2. Use a brush to clean the chain of cutting residue and
dirt.
Illustration AA
3. Clean the housing and handles with a soft, dry cloth.
4. Check the function of the chain brake after every
cleaning (see Chapter Checking the functionality of
the chain brake).

Maintenance intervals

The following activities must be carried out before every
use:
 Check the filling level of the chain oil, top up the
chain oil if necessary (see Chapter Filling the chain
oil tank).
 Check the chain tension (see Chapter Checking the
chain tension).
 Check the chain for sufficient sharpness, if neces-
sary replace the chain (see Chapter Replacing the
chain and guide rail).
 Check the device for damage.
 Check all pins, nuts and screws for tightness.
 Check the function of the chain brake (see Chapter
Checking the functionality of the chain brake).
Every 5 operating hours
 Check the function of the chain brake every 5 oper-
ating hours (see Chapter Checking the functionality
of the chain brake).
English
Before every use