Tabla de contenido
Idiomas disponibles
Idiomas disponibles
GB
IE
•
Kinks caused by improper attachment or routing of the
connection cable.
•
Cut surfaces caused by vehicles driving over the connection
cable.
•
Insulation damage caused by tearing out of the wall socket.
•
Cracks resulting from the insulation becoming old.
Such faulty electrical connections must not be used and may
endanger life due to the damage to the insulation.
Electrical connection cables should be checked regularly for
damage. Ensure that during such checks, the connection cable is
not connected to the mains.
Electrical connection cables must comply with the relevant VDE
and DIN regulations. Only use connection cables with the mar-
king H05VV-F.
It is stipulated by law that the type of connection cable must be
printed on it.
Alternating Current Motor
•
The mains voltage must be 230 V~.
•
Extension cables up to 25 m in length must have a cross-sec-
tion of 2.5 mm².
Connections and repairs to the electrical equipment may only be
please provide the following information:
•
Current type of the engine
•
Data from the machine type plate
•
Data from the motor type plate
•
Assembly
Prior to first use, check the tightness of the
outer flange of the saw blade.
Assembly, Replacement of Parts and Adjustments
Caution! The mains plug must be removed before all
servicing, retooling and assembly work.
the parts which are similar.
Note: If connections are secured with a bolt (round head/or
hexagonal), hexagonal nuts and a washer, the washer must be
placed under the nut.
Insert the bolts from the outside to the inside in each case, secu-
ring the connections with nuts from the inside.
Note: Tighten the nuts and bolts during assembly only to the
extent that they cannot fall off.
Mounting of the Frame
(Figures 4-9)
2. Screw the four legs (20) with the round head bolts (a) from
bag A loosely onto the saw (Figure 6). Use the ring spanner
(g) supplied for this.
3. Now screw the four centre struts (21, 22) loosely to the legs
(20) and together with the round head screws (a) (Figure 7).
Caution: The longer centre struts (22) must be
used laterally and are mounted in front of the
shorter centre struts (21).
26
4. Then tighten all bolts.
5. Now attach the rubber feet (23) to the legs (20) (Figure 8).
6. Screw the stand brackets (24) into the rear legs using the
drill holes. Mounting material: 2 each round head bolts (a) ),
(Figure 9).
Caution! Both stand brackets must be attached to
the rear of the machine at attachment points 25!
Mounting the table width
and length extension
(Figures 10-14)
1. Loosely tighten the table width extension (7) and table length
extension (17) on the saw table using the hexagon bolts (b).
(Figure 11). The 'Parkside' logo on the table extensions (7)
points away from the saw table (1).
2. Loosely tighten the table supports (26, 27) on the housing
and the table width extension (7) or table length extension
(17) of the table circular saw using the hexagonal screws (b)
from bag B. The short supports (26) are for the table wide-
ning extension, the long supports (27) for the length extensi-
on, (Figures 12, 13).
3
table.
4. Then tighten all bolts.
5. Place the table circular saw on the base frame (13).
6. Screw the four screws (d) onto the side of the table width
extension (7) or table length extension (17) (see Fig. 2) and
hang the collection bag for wood residues (15) on the four
screws.
Mounting / adjusting the Riving Knife
Insert the battery
Caution! Remove the mains plug! The setting of the
saw blade (4) must be checked whenever a blade has
been replaced.
1. Inserting the batteries (Figure 15):
-
Turn the laser on/off switch (36) to the 0 position (laser off).
-
Remove the battery compartment cover (38) by loosening the
screw (37). Now remove the battery compartment cover (38)
by bending at the side.
-
Insert the batteries supplied (type AAA), ensuring the correct
polarity (see Figure 15).
-
Put the battery compartment cover (38) back in position and
tighten it with the screw (37). Notes concerning the batteries:
-
If you are not going to use the laser for a prolonged period,
please remove the batteries from the battery compartment.
device.
-
Do not place the batteries on radiators or expose them for a
prolonged period to strong sunlight; temperatures above
45 ° could damage the device.
(Figures 16-20)
2. Adjust the saw blade (4) to a max. cutting depth, move to
the 0° position and lock in place.
3. Dismantle the saw blade guard (2)
(not during initial assembly).
(Figures 15-20)
Capítulos
Tabla de contenido
