Low Battery - DeWalt DCN690 Traducido De Las Instrucciones Originales

BUMP ACTION MODE (DCN690, DCN692)
The bump action mode is used for rapid nailing on
flat, stationary surfaces and typically most effective
for application driving shorter nails.
1. Using the mode selector switch (i) to select the
bump action mode ( ).
2. Release the trigger safety lock-off (b).
3. To drive a single nail, operate the tool as
described for sequential action:
a. Push the contact trip (c) against the work
surface.
b. Pull the trigger switch (a) to actuate the tool.
Each trigger pull with the contact trip pushed
against the work surface will drive one nail.
4. To drive several nails, depress and hold the
trigger switch (a), and then push the contact trip
(c) repeatedly against the work surface.
WARNING: Do not keep the trigger
depressed when the tool is not in use.
Keep the trigger safety lock-off (b) in the
locked position to prevent accidental
actuation when the tool is not in use.
5. When changing between sequential and
bump modes, it may be necessary to adjust the
driving depth. Refer to Adjusting the Driving
Depth for instructions.
Using the Trigger Lock-off (fi g. 3)
Each D WALT nailer is equipped with a trigger lock-
E
off (b) which when pushed to the right as shown
in Figure 3, prevents the tool from firing a nail by
locking the trigger and bypassing power to the
motor.
When the trigger lock-off is pressed to the left,
the tool will be fully operational. The trigger lock-
off should always be locked off whenever any
adjustments are made or when tool is not in
immediate use.
Non-mar Tip (fi g. 1)
When using this tool on materials that you do not
want to mark, such as wood cladding, use the
plastic non-mar tip (m) over the contact trip (c).
NOTE: For maximum depth of drive, especially
with long nails, the non-mar covered should be
removed.
LED Indicator (fi g. 1)
Your nailer is equipped with two LED indicator lights
(e) located on the back of the tool just below the
back cap. Also refer to to the Troubleshooting
Guide for further instruction.

LOW BATTERY

Replace battery with a
charged pack.
HOT PACK
Let the battery cool or
replace it with a cool pack.
JAM/STALL CONDITION
Rotate the stall release
lever to release. Refer to
Stall Release.
HOT TOOL
Let the tool cool down
before continuing use.
ERROR
Reset tool by removing
and reinserting battery
pack or cycling trigger lock
+/OR
or any other
off. If error code persist,
combination.
take tool to an authorized
D WALT service center.
E
Stall Release (fi g. 1, 3)
If the nailer is used in rigorous application where
all available energy in the motor is used to drive
a fastener, the tool may stall. The driver blade did
not complete the drive cycle and the jam/stall
indicator (e) will flash. Rotate the stall release lever
(f) on the tool and the mechanism will release. If the
driver blade does not automatically return to the
home position, proceed to Clearing a Jammed
Nail. If the unit continues to stall please review the
mode selection, material and fastener length to be
sure that it is not too rigorous an application.
DCN692
If continuous stalling occurs, review speed selection.
Depending upon the application, a different speed
setting may be necessary.
Clearing a Jammed Nail (fi g. 1, 3)
If a nail becomes jammed in the nosepiece, the
jam/stall indicator light (e) will flash.
NOTE: The jam could be as a result of debris build
up in the nose channel. Please check and clear
out any debris as outlined below immediately if you
notice any change of performance in the tool.
1. Remove battery pack from tool and engage
trigger safety lock-off (b).
2. Slide the spring-loaded pusher latch (h) to the
base of the magazine to lock it into place and
unload nail strip.
EN GL IS H
57