Residual Risks; Electrical Safety; Important Safety Instructions For All Battery Chargers - DeWalt DCN692 Traducido De Las Instrucciones Originales

ENGLIsh
• Do not use the DCN692
ʵ when changing from one driving location to another
involving the use of scaffoldings, stairs, ladders or ladder-
like constructions, e.g., roof laths, etc.;
ʵ when closing boxes or crates;
ʵ when fitting transportation safety systems, e.g., on
vehicles, wagons, etc.
For exemptions check your local national workplace regulations.
• Always check local workplace regulations.
• Do not use the tool as a hammer.
• Never actuate the fastener driving tool into free space.
• In the work area, carry the tool at the workplace using only
one handle, and never with the trigger actuated.
• Consider the conditions in the work area. Fasteners can
penetrate thin work pieces or slip off corners and edges of the
work piece, and thus put people at risk.
• Do not drive fasteners close to the edge of the workpiece.
• Do not drive fasteners on top of other fasteners.

Residual Risks

The following risks are inherent to the use of these machines:
• Injuries caused by improper handling of the tool.
• Loss of control due to not gripping tool firmly.
• Muscle strain of arms and hands, especially when working
overhead. Always take regular breaks when working for long
periods of time.
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot
during operation.
• Risk of personal injury due to prolonged use.
• Loss of control caused by recoil.
• Risk of injury caused by pinch points, sharp edges and
improper handling of workpiece.
• Risk of injury caused by sharp edges when changing nails or
inserting nail sticks.

Electrical Safety

The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
your charger corresponds to that of your mains.
Your D WALT charger is double insulated in
e
accordance with EN60335; therefore no earth wire
is required.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the D
service organisation.
42
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 3 A.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1 mm
is 30 m.
When using a cable reel, always unwind the cable completely.
Chargers
D WALT chargers require no adjustment and are designed to be
e
as easy as possible to operate.
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual contains important
safety and operating instructions for compatible battery
chargers (refer to Technical Data).
• Before using charger, read all instructions and cautionary
markings on charger, battery pack, and product using
battery pack.

WARNING: Shock hazard. Do not allow any liquid to get
inside charger. Electric shock may result.

WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.

CAUTION: Burn hazard. To reduce the risk of injury,
charge only D
batteries may burst causing personal injury and damage.

CAUTION: Children should be supervised to ensure that
they do not play with the appliance.
NOTICE: Under certain conditions, with the charger
plugged into the power supply, the exposed charging
contacts inside the charger can be shorted by foreign
material. Foreign materials of a conductive nature such
as, but not limited to, steel wool, aluminum foil or any
buildup of metallic particles should be kept away from
charger cavities. Always unplug the charger from the
power supply when there is no battery pack in the cavity.
Unplug charger before attempting to clean
• DO NOT attempt to charge the battery pack with any
WALT
e
chargers other than the ones in this manual. The charger
and battery pack are specifically designed to work together.
2 ; the maximum length
SAVE THESE INSTRUCTIONS
WALT rechargeable batteries. Other types of
e