Optional Accessory - Makita LS1019 Manual De Instrucciones

Ocultar thumbs Ver también para LS1019:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 98
In the case of right bevel cut
(a) (b)
1. Inside corner 2. Outside corner
Table (A)
Molding
Bevel angle
position
52/38°
in the
type
figure
For
(a)
Right
inside
33.9°
corner
(b)
For
(c)
outside
(d)
corner
Table (B)
Molding
position in
the figure
For inside
(a)
corner
(b)
For outside
(c)
corner
(d)
Example:
In the case of cutting 52/38° type crown molding for
position (a) in the above figure:
Tilt and secure bevel angle setting to 33.9° RIGHT.
Adjust and secure miter angle setting to 31.6°
RIGHT.
Lay crown molding with its broad back (hidden)
surface down on the turn base with its WALL
CONTACT EDGE against the guide fence on the
saw.
The finished piece to be used will always be on
the RIGHT side of the blade after the cut has been
made.
(c) (d)
1
2
Miter angle
45° type
52/38°
type
Right
Right
30°
31.6°
Left
31.6°
Right
31.6°
Molding
Finished
edge against
piece
guide fence
Wall contact
Finished
edge should
piece will be
be against
on the Right
guide fence.
side of blade.
Ceiling
contact edge
Finished
should be
piece will be
against guide
on the Left
fence.
side of blade.
Wall contact
edge should
be against
guide fence.
Crown molding stopper

Optional accessory

Crown molding stoppers allow easier cuts of crown
molding without tilting the saw blade. Install them on the
turn base as shown in the figures.
At right 45° miter angle
► Fig.49: 1. Crown molding stopper L 2. Crown mold-
At left 45° miter angle
► Fig.50: 1. Crown molding stopper L 2. Crown mold-
Position crown molding with its WALL CONTACT EDGE
against the guide fence and its CEILING CONTACT EDGE
against the crown molding stoppers as shown in the figure.
Adjust the crown molding stoppers according to the size of
the crown molding. Tighten the screws to secure the crown
molding stoppers. Refer to the table (C) for the miter angle.
► Fig.51: 1. Guide fence 2. Crown molding stopper
45° type
Right
35.3°
Left
35.3°
Right
35.3°
1. Inside corner 2. Outside corner
Table (C)
For inside
corner
For outside
corner
Cutting aluminum extrusion
► Fig.52: 1. Vise 2. Spacer block 3. Guide fence
When securing aluminum extrusions, use spacer blocks or pieces
of scrap as shown in the figure to prevent deformation of the alumi-
num. Use a cutting lubricant when cutting the aluminum extrusion
to prevent build-up of the aluminum material on the blade.
WARNING:
round aluminum extrusions. Thick or round alumi-
num extrusions can be difficult to secure and the work
may loosen during the cutting operation which may
result in loss of control and serious personal injury.
26 ENGLISH
ing stopper R 3. Turn base 4. Guide fence
ing stopper R 3. Turn base 4. Guide fence
(a) (b)
(c) (d)
1
Molding
Miter angle
position in
the figure
(a)
Right 45°
(b)
Left 45°
(c)
(d)
Right 45°
4. Aluminum extrusion 5. Spacer block
Never attempt to cut thick or
2
Finished
piece
Save the right
side of blade
Save the left
side of blade
Save the right
side of blade
Save the left
side of blade
Tabla de contenido
loading

Este manual también es adecuado para:

Ls1019l

Tabla de contenido