Clock Adjustment; Reheat Function - Redmond RMC-M4502E Guia Del Usuario

Keep all warning labels, including the serial number identification label located on the housing.
Wipe the housing of the appliance with a soft, damp cloth. Rinse the inner bowl with warm soapy water and
dry thoroughly. An odour on first use of the appliance is normal and does not indicate a malfunction. In such
case, clean the appliance, following "Cleaning and Maintenance".
After transportation or storage at low temperatures allow the appliance to stay at room temperature
for at least 2 hours before using it.
II. OPERATION
Before Use
Place the device on a flat, stable, and hard surface away from any objects or cabinets that could be damaged
by steam, humidity, or high temperatures.
Before operating, make sure that the outer and inner parts of the multicooker have no dents, cracks or any
other visible damages. There should not be any obstructions between the heating element and the bowl.

Clock Adjustment

1. Plug in the unit. Press and hold down the "Preset" button for 3 seconds, the minute indicator of the current
time will start flashing.
2. Press "Cooking Time" button repeatedly to set the minutes (setting interval is 1 minute). If the button is
pressed for more than 3 seconds, the accelerated time adjustment will start. Press "Hour/Min" at the end
of the minute adjustment, the hour indicator will start flashing.
3. Set the hour value by pressing "Cooking Time". The interval is 1 hour. If the button is pressed for more than
3 seconds, the accelerated time adjustment will start.
4. When you finish entering the data press "Cancel/Reheat" button or do nothing for a few seconds to save
your settings. Time indicator stops blinking.
Cooking Time Adjustment
Multicooker REDMOND RMC-M4502E allows manually adjusting the cooking time, set by default for each
programme. Setting interval and time adjustment range depend on the programme chosen.
1. Press "Hour/Min" button, minute indicator starts blinking. Press "Cooking time" button repeatedly to adjust
the minutes. If the button is pressed for more than 3 seconds, the accelerated time adjustment will start.
2. Press "Hour/Min" button, hour indicator starts blinking. Press "Cooking time" button repeatedly to adjust
the hours. If the button is pressed for more than 3 seconds, the accelerated time adjustment will start.
3. If it' s necessary to set the cooking time to less than one hour, successively press the "Cooking Time" button
in the hour adjustment mode until the hour indicator goes out. Press "Hour/Min", the minute indicator
will start flashing. Set the desired minute value by successive pressing the "Cooking Time" button.
4. To cancel previous settings press the "Cancel/Reheat" button (after that you will need to re-enter the
cooking programme).
If the automatic programme is manually adjusted the appliance immediately sets the minimum cooking
time!
8
This is a non-volatile memory unit. In case of a short term power cut-off all settings, including Preset function,
will be saved.
"Preset" Function
Time delay function allows programmeming the cooking programme to be over by certain time. The programme
can be delayed for a period of time from 10 minutes to 24 hours with 10 minute intervals. The appliance is
equipped with two independent timers, allowing to record the time by which the dish is typically cooked. To
set the Timer:
1. Press "Menu" to select the automatic cooking programme.
2. Press "Preset" to select the Preset 1 or Preset 2 memory cells.
3. Press "Hour/Min" to enable the hour adjustment mode on the timer, the hour indicator will start flashing.
4. Set the desired hour value by pressing "Cooking Time". The interval is 1 hour.
5. Press "Hour/Min" to enable the minute adjustment mode. Minute indicator starts blinking.
6. Set the desired minute value by pressing "Cooking Time". The interval is 10 minutes.
7. Press "Start" at the end of the time adjustment. The "Start", "Cancel/Reheat" and "Preset" button indicators
will light up. The dish readiness time will be displayed.
Setting the Preset function remember that the countdown in some programs begins only when the
device reaches its operating temperature.
"Keep Warm" Function
This function automatically activates in the standby mode together with the start of the selected cooking
programme and when the programme is complete, keeps the ready food warm at 70-75°С for 24 hours. When
Keep Warm is enabled the "Cancel/Reheat" indicator lights up, the programme countdown is displayed at the
end of the cooking programme. Press "Cancel/Reheat" button to disable the function. Button indicator goes
off.
When cooking dishes in the "MULTI-COOK" programme at the temperature not higher than 80°С the
Keep Warm function will be disabled.
Preliminary Disabling the "Keep Warm" Function
You can disable the Keep Warm function right after the start of any programme. To do so after selecting the
cooking programme (after pressing the "Start" button) press and hold down the "t°C / Keep Warm ON/OFF"
button for 3 seconds. The "Cancel/Reheat" button indicator will go out. Repressing and holding down the "t°C /
Keep Warm ON/OFF" button for 3 seconds will re-enable Keep Warm. The "Cancel/Reheat" button indicator
will light up. This function is also available when using the Time Delay function.

Reheat Function

The multicooker REDMOND RMC-M4502Е can be used for reheating cold meals. Just put the ready dish into
the bowl, install it into the multicooker, close the lid, press the "Cancel/Reheat" button until an audible signal
is heard. After a while the appliance will reheat the dish to 70-75°С and keep it warm for 24 hours. Repress
"Cancel/Reheat" to disable Reheat.