Detection Of Obstacles (Amperometric Sensor, Encoder, Safety Ribbons); Amperometric Sensor; Encoder; Safety Ribbons - V2 HEAVY1 Manual De Instrucciones

12 - DETECTION OF OBSTACLES
(AMPEROMETRIC SENSOR, ENCODER,

SAFETY RIBBONS)

The presence of an obstacle that prevents the movement of the
door can be detected in several ways:

1. Amperometric sensor

2. Encoder

3. Safety ribbons
Regardless of the device that detected the obstacle, the reaction
of the unit depends on the value set for the parameter
obstacles during opening and
• If the value is , the port is simply stopped
0.0"
• If the value ranges between
the movement for the time set
• If the value is the door re-closes or re-opens completely.
FULL
m
Following detection of an obstacle during closure,
the door reopens and the behaviour of the power centre
depends on various parameters, with the following priority:
1. If the clock mode is active (
pause time for automatic closure is activated.
2. If the door is closed without withdrawing (
or if closure after the obstacle is manual (
counting of the pause time for automatic closure is NOT
activated and the door will start moving again after the next
start-up command is given
3. If closure after the obstacle is automatic (
the centre will behave according to the settings of the
parameter
12.1 - AMPEROMETRIC SENSOR
An unexpected increase in the consumption of current by the
motor is meant as the result of the presence of an obstacle.
This feature is automatic and requires no settings.
12.2 - ENCODER
The unit detects the presence of an obstacle when the encoder
indicates that the motor is turning at a speed lower than the set
one (Chapter 18).
The sensitivity of the encoder must be set via the
parameter: the higher the value, the more the unit will be
responsive to small drops in speed. If you do not want the
encoder to detect obstacles, set to
12.3 - SAFETY RIBBONS
The unit detects the presence of an obstacle when a safety ribbon
is pressed.
The unit has two inputs for the ribbons, which can be
independently enabled and associated with different types of
function.
Connect safety ribbon 1 (COS1) to terminals S7 and S9 and
configure parameter to activate entry
COS1
Connect safety ribbon 2 (COS2) to terminals S8 and S9 and
configure parameter to activate entry
COS2
OST.A
for obstacles during closing:
OST.C
and the door reverses
0.5" 4.5"
= ), counting of the
MODE OROL
= ),
OST.C 0
=
CH.OS MAN
=
CH.OS AUTO
CH.AU
S.ENC
.
0
• If you set
AP
during opening and the unit will operate according to the
settings of the
• If you set
CH
during closing and the unit will operate according to the
settings of the parameter
• If you set
APCH
opening and closing:
- when opening the control unit will operate according to the
settings of the parameter
- when closing the control unit will operate according to the
for
settings of the parameter
m
WARNING:
• If you do not connect any ribbon to the terminal S7, the
parameter
COS1
• If you do not connect any ribbon to the terminal S8, the
parameter
COS2
),
),
parameter
COS1
parameter
COS2
The control unit can operate with different types of ribbons;
depending on the type of ribbon used it is required to correctly set
the parameter
CO.TE
NOTE: You can not use different types of ribbons on two COS1
and COS2 inputs.
a. Mechanical ribbons with normally closed contact
Set the parameter
before the movements.
b. Optical ribbons
Set the parameter
movement a functional test similar to that of photocells is
carried out. If you do not want the test to be run, set
Connect the power supply of the optical ribbons following the
instructions described in chapter 11.2
c. Ribbon with resistive rubber
Set the parameter
expected to measure an impedance equal to 8.2 kohms, and
an alarm is triggered if a lower impedance (pressed ribbon) or a
higher impedance (interrupted wire) are detected, therefore it
is not necessary to run the test before the movements.
m
WARNING: If you connect multiple ribbons to the same
terminal, the connection must be made in series, except in the
case of resistive ribbons which which must be connected in
parallel.
- 36 -
the operation of the ribbon is detected only
parameter
OST.A
the operation of the ribbon is detected only
OST.C
the operation of ribbon is detected during the
OST.A
OST.C
must be set to .
NO
must be set to .
NO
S1 S2 S3 S4 S5 S6 S7 S8 S9
COS1
a
DEFAULT = (no function)
NO
a
DEFAULT = (no function)
NO
with the value
CO.TE NO
with the value
CO.TE FOTO
with the value
CO.TE RESI
COS2
: not test is run
: before any
.
NO
: the unit is