Important - Wayne Dalton 9100 Instrucciones De Instalación Y Manual Del Propietario

12
Operator Bracket
NOTE: Operator bracket must be
Tools Needed:
mounted and secured prior to installing
Power Drill
top section.
7/16" Socket

IMPORTANT:

Driver
TROLLEY TYPE OPERATOR ON 9100,
Vice Clamps
9400, AND 9600 SERIES DOORS, A
Phillips Head
WAYNE-DALTON TROLLEY BRACKET
Screwdriver
MUST BE SECURELY ATTACHED TO
THE TOP SECTION, ALONG WITH ANY
U-BAR'S INITIALLY PROVIDED WITH THE
DOOR. IT IS THEN UNNECESSARY TO
FURTHER REINFORCE THE TOP SECTION
OF THE ABOVE MODEL WAYNE-DALTON
DOOR, WHEN ATTACHING A TROLLEY
TYPE OPERATOR, AS LONG AS THE
INSTALLATION OF THE OPERATOR
IS ACCORDING TO INSTALLATION
INSTRUCTIONS AND OWNER'S MANUAL
AND FORCE SETTINGS ARE ADJUSTED
PROPERLY.
Prior to installing top section, locate the
center of the top section and seat the
operator bracket on male part of the top
section. For retro fi t applications, the
operator bracket must be aligned with
an existing operator and positioned on
top section so it bridges the transition
point of the section thickness, as shown
in FIG. 1.1 and 1.2. Install (2) #12 x 1/2"
phillips head screws on the opposite
side of operator bracket, as shown in
FIG. 1.3. Clamp operator bracket to u-bar
(if furnished), as shown in FIG. 1.4. First
attach (4) 1/4" - 14 x 5/8" self-tapping
screws to the operator bracket, as
shown in FIG. 1.5. Then attach (2) 1/4"
- 14 x 5/8" self-tapping screws to the
operator bracket, as shown in FIG. 1.6.
Remove vice clamps.
NOTE: If you have a 9100 door, (2) of the
1/4" - 20 x 11/16" self-drilling screws
used to attach the u-bar instead of (2)
1/4" - 14 x 5/8" self-tapping screws
when attaching operator bracket to u-
bar, as shown in FIG. 1.6.
NOTE: When attaching operator
bracket to top section with u-bar, apply
additional pressure to thread into the
u-bar.
NOTE: See FIG. 1.7 for installing operator
bracket on top section without u-bars.
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com
WHEN INSTALLING A
SECTION
WITH OR
WITHOUT
(4) 1/4" - 14 X 5/8"
ALIGN CENTER OF BOTH TABS WITH
CENTER LINE OF TOP SECTION
OPERATOR
BRACKET
TOP
FIG. 1.1
U-BAR
OPPOSITE SIDE OF
OPERATOR BRACKET
(2) #12 X 1/2"
PHILLIPS HEAD
SCREWS
FIG. 1.3
OPERATOR
BRACKET
SELF-TAPPING
SCREWS
FIG. 1.5
FIG. 1.7
MALE PART OF
OPERATOR
TOP SECTION
BRACKET
U-BAR
TOP
SECTION
FIG. 1.2
OPERATOR BRACKET
VICE CLAMP
NOTE: NOT REQUIRED
FOR J-STRUTS.
FIG. 1.4
(2) 1/4" - 14 X 5/8"
SELF-TAPPING
SCREWS
OPERATOR
BRACKET
(2) 1/4" - 20 X 11/16"
SELF-DRILLING SCREWS
FIG. 1.6
(6) 1/4" - 14 X 5/8"
SELF-TAPPING
SCREWS
OPERATOR
BRACKET
17