Wolf Garten NX9 Instrucciones De Funcionamiento página 11

English
PTO lever (depending on
model)
Fig. 11
The PTO lever actuates a mechanism
to switch ON and OFF the cutters.
Switch off cutter deck
Press lever out of recess and pull
all the way backwards.
Switch on cutter deck
Slowly press lever forwards and
engage in recess.
PTO switch
(depending on model)
Fig. 12
The PTO switch actuates an mecha-
nical clutch to switch ON and OFF
the cutters.
ON = pull the switch.
OFF = press the switch.
Note: When the safety lock system
has automatically switched OFF
the appliance (e.g. when reversing
with activated cutters), first switch
ON and then OFF the PTO switch
to release the lock on the clutch.
Parking brake/
Speed control
Fig. 13
This switch has a dual function
on some models:
Actuate the parking brake:
Press down the brake pedal fully,
and press the switch.
Release the parking brake:
Press down the brake pedal fully,
the switch disengages.
Tempomat switch
on (depending on model):
When driving, press the switch.
The forward speed selected at this
point (but not top speed) is maintai-
ned, and the drive pedal can be re-
leased.
When the accelerator pedal or the
brake pedal is depressed, the cruise
control automatically switches off.
8
Drive pedal for appliances
with hydrostatic drive
Fig. 14
The drive pedal is used to adjust the
speed continuously and to change
=
direction:
Forwards = push forwards the drive
pedal (in direction
=
forward, the faster.
Stop (for stationary vehicle and
changing direction) = release
the drive pedal (N).
Reverse = push back the drive
pedal (counter to direction
the further back, the faster.
Drive pedal for appliances
with auto drive
Fig. 15
The drive pedal is used to adjust
the speed continuously:
– Move the direction-of-travel lever
to "F" (forwards) ( ) or "R"
(reverse) ( ).
– Forwards = push forwards
the drive pedal (in direction),
thefurther forward, the faster.
Transmission release for
machines with a hydrostatic
drive
Fig. 16
To push the unit when the engine
is switched off.
Depending on model:
■ Pull out lever and press down
(Fig. 16a). To drive the unit,
push lever up and press in.
or
Pull out lever and press up
■
(Fig. 16b). To drive the unit,
push lever down and press in.
The lever is situated on the rear panel
of the machine.
Display cluster
(depending on model)
Fig. 17
According to the model, the combi-
nation indicator can consist of the
following elements.
Operating instructions for lawn tractors
Oil pressure (1):
The indicator light is lit while the
engine is running, immediately
switch off engine and check oil level.
Where necessary, visit a garage.
Brake (2):
Indicator lamp lights up if the brake
pedal is not depressed or the
), the further
parking brake is not locked when
the engine starts.
Cutter deck (PTO) (3):
Indicator lamp lights up if the cutter
deck (PTO) is not switched off when
the engine starts.
),
Battery charge indicator (4):
If the indicator light lights up when
the engine is running, this means
that the battery is not sufficiently
charged. Where necessary, visit
a garage.
Operating hours counter (5):
Indicates the completed operating
hours when the ignition is switched
on.
Ampere meter (6):
This shows the charging current
from the generator to the battery.
– When the ignition is switched on,
the battery voltage indicator
is indicated for a short period
and then the operating hours
are indicated.
The operating hours are always
counted except for when the ignition
key is in the "Stop" position or when
it is removed.
– Each time 50 operating hours have
elapsed (according to the model),
the oil change indicator "CHG/OIL"
appears in the display for five
minutes. This message appears
after the next two hours of opera-
tion. See the engine manual for oil
change intervals.
Seat
(depending on model)
Fig. 18
a) Pull the lever, and adjust the seat.
or
b) Loosen adjusting screw, adjust
seat and retighten adjusting screw.
Optional functions: