Transport And Storage - salmson AQUAVAL 56-1 Instrucciones De Montaje

Tabla de contenido
Idiomas disponibles

Idiomas disponibles

ENGLISH
1. GENERAL
1.1 Applications
Pumps designed for :
Rainwater, muddy water, sand-containing water, silt-containing
water, with the exclusion of sanitary waste, sewer water and seawa-
ter.
Drainage of all work sites :
• Construction, mines,
• Building sites,
• Civil engineering.
1.2 Technical characteristics
• Max. flow
• Max. head
• Max. immersion depth
• Max. temperature
* 10 min max. at 60°C under intermittent operation.
2. SAFETY
Read this data sheet carefully before installing and starting up. Pay
special attention to the points concerning the safety of the equip-
ment for the intermediate or end user.
2.1 Symbols used in this manual
Calls attention to a potential risk affecting the safety of
persons.
Instructions concerning electricity.
Indicates an instruction whose the non observa-
CAUTION !
tion can create a damage for the equipment and
its functioning.

3. TRANSPORT AND STORAGE

When the equipment is delivered, check that it has not been dama-
ged in transit. If any defects are found, make the necessary arrange-
ments with the carrier.
If the equipment delivered is to be installed at
CAUTION !
some later time, store it in a dry place and protect
it from impacts and all outside influences (moisture, frost, etc.).
4. PRODUCTS AND ACCESSORIES
Aquaval type
ND of threa- Approx. Strainer
ded discharge mass.
(56-32 thread)
56-1 M or T4
1/4"
56-15 T4
2"
56-32 T4
3"
56-50A-T4- H-M or B
4"
56-100A-T4- H-M or B
4"
4.1 Technical description (See FIG. 1)
1
- Submersible units.
2
- Level regulator (switches with counterweights).
3
- Isolation valve suitable for fluid pumped.
4
- Non-return valve.
5
- Discharge pipes.
6
- Chain for hoisting and lowering the unit.
7*
- Control and protection box (or switch).
8
- Air purge hole Ø 4 mm on discharge pipe (fixed installation).
* Yn 4100 : one pump with 3 level regulators.
Yn 4200 : two pumps in parallel with 4 level regulators.
: 175 m3/h
: 48 m
: 12 m
: 40° C *
Connector
mesh
for tube dia.
Kg
14.5
10x10
33-42
18.5
10x10
50-60
29
5x8
80-90
53
8x25
102-104
66
8x25
102-104
4.2 The pump
- Submersible, monobloc.
- Vertical discharge (horizontal for 56-15).
- Common shaft, motor pump.
- Single-stage with a closed wheel with wide passage equipped with
a front wear ring and a rear wear plate (except 56-1 and 56-15).
- Motor-pump oil-containing intermediate chamber, lubricating both
mechanical seals.
4.3 The motor
- Sealed, with oil and pumped-water cooling (except 56-1).
- Direct start.
- Speed
- Winding
Three-phase : 230-400 V
Single-phase : 230 V (56-1-M)
- Capacitor
- Frequency
- Insulation class
- Protection index
Aquaval
Type
P2
kW
56-1 M or T4
0.75
56-15 T4
1.30
56-32 T4
2.36
56-50A-T4- H-M or B
3.70
56-100A-T4- H-M or B
7.0
4.4 Accessories (optional)
• Hoist chain.
• Yn 4000 control box or other.
• Overflow audible alarm.
• Level regulators.
• 439 D or 439-E24 circuit breaker.
• Ball non-return valve.
• Isolation valve (depending on fluid).
• Air-pressure switch (IPA).
• Cable kit: 5, 10, and 20 m lengths with duplicate molded pump
connector plugs and support flange – for Aquaval: 56-1M (with
capacitor case) –56-1-T/56-15-T/56-32-T.
5. INSTALLATION
5.1 Mounting
- The compact design of this pump makes it easy to use in a lift pum-
ping station. The float level regulators, offered as an accessory,
allow automatic operation. The pump is designed for operation
completely submerged in the liquid to be pumped. The level regu-
lators must not be disturbed by splashes resulting from the arrival of
water in the well.
- It allows the water level to be brought down within a few centime-
ters of the bottom and in the event of a continuous arrival of water,
it can continue to pump while snorting.
- Complete pump installation using accessories in accordance with
needs; we recommend the installation of a ball non-return valve.
- If the ground on which the pump is placed is not stable, it is recom-
mended to either hang it by its handle or install it on a stable plat-
form to avoid the rapid fouling of the filter or the pump sinking into
the mud.
- In the presence of fibrous material (grass, leaves, etc.) in the pum-
ped water, place the pump in a basket.
- Never handle or hang the unit by its power cord.
- Lower the unit using a chain attached to the hoist ring.
7
: 2900 rpm
: 20 µF-450 V (56-1-M)
: 50 Hz (contact us for 60 Hz)
: B
: IP68
Power
Rated current
motor
(A) at
P1
1~
3~
kW
230 V
230 V
1.2
5.3
3.6
2.0
-
5.8
2.9
-
8.2
4.9
-
14.2
9.0
-
25.5
3~
400 V
2.1
3.35
4.7
8.1
14.8
Tabla de contenido
loading

Este manual también es adecuado para:

Aquaval 56-50Aquaval 56-32

Tabla de contenido