Makita LS1219 Manual De Instrucciones página 26

Table (B)
– Molding
position in
WKH ¿JXUH
For inside (a)
corner
(b)
For outside (c)
corner
(d)
Example:
In the case of cutting 52/38° type crown molding for
SRVLWLRQ D LQ WKH DERYH ¿JXUH
‡ 7LOW DQG VHFXUH EHYHO DQJOH VHWWLQJ WR  ƒ /()7
‡ $GMXVW DQG VHFXUH PLWHU DQJOH VHWWLQJ WR ƒ
RIGHT.
‡ /D\ FURZQ PROGLQJ ZLWK LWV EURDG EDFN KLGGHQ
surface down on the turn base with its CEILING
&217$&7 ('*( DJDLQVW WKH JXLGH IHQFH RQ WKH
saw.
‡ 7KH ¿QLVKHG SLHFH WR EH XVHG ZLOO DOZD\V EH RQ
the LEFT side of the blade after the cut has been
made.
In the case of right bevel cut
(a) (b)
1
1. Inside corner 2. Outside corner
Table (A)
– Molding Bevel angle
position
52/38°
in the
W\SH
¿JXUH
For (a) Right
inside 33.9°
corner
(b)
For (c)
outside
(d)
corner
Molding Finished
edge against piece
guide fence
Ceiling Finished
contact edge piece will be
should be on the Left
against guide side of blade.
fence.
Wall contact
edge should
Finished
be against
piece will be
guide fence.
on the Right
Ceiling side of blade.
contact edge
should be
against guide
fence.
(c) (d)
2
Miter angle
ƒ W\SH 52/38° ƒ W\SH
W\SH
Right Right Right
30° 31.6° 35.3°
Left Left
31.6° 35.3°
Right Right
31.6° 35.3°
Table (B)
– Molding
position in
WKH ¿JXUH
For inside
corner
For outside
corner
Example:
In the case of cutting 52/38° type crown molding for
SRVLWLRQ D LQ WKH DERYH ¿JXUH
‡ 7LOW DQG VHFXUH EHYHO DQJOH VHWWLQJ WR  ƒ 5,*+7
‡ $GMXVW DQG VHFXUH PLWHU DQJOH VHWWLQJ WR ƒ
RIGHT.
‡ /D\ FURZQ PROGLQJ ZLWK LWV EURDG EDFN KLGGHQ
VXUIDFH GRZQ RQ WKH WXUQ EDVH ZLWK LWV :$//
&217$&7 ('*( DJDLQVW WKH JXLGH IHQFH RQ WKH
saw.
‡ 7KH ¿QLVKHG SLHFH WR EH XVHG ZLOO DOZD\V EH RQ
the RIGHT side of the blade after the cut has been
made.
Crown molding stopper
Optional accessory
Crown molding stoppers allow easier cuts of crown
molding without tilting the saw blade. Install them on the
WXUQ EDVH DV VKRZQ LQ WKH ¿JXUHV
At right 45° miter angle
Fig.49: 1. Crown molding stopper L 2. Crown mold-
ing stopper R 3. Turn base 4. Guide fence
At left 45° miter angle
Fig.50: 1. Crown molding stopper L 2. Crown mold-
ing stopper R 3. Turn base 4. Guide fence
3RVLWLRQ FURZQ PROGLQJ ZLWK LWV :$// &217$&7 ('*(
DJDLQVW WKH JXLGH IHQFH DQG LWV &(,/,1* &217$&7
EDGE against the crown molding stoppers as shown in
WKH ¿JXUH $GMXVW WKH FURZQ PROGLQJ VWRSSHUV DFFRUGLQJ
to the size of the crown molding. Tighten the screws to
secure the crown molding stoppers. Refer to the table
(C) for the miter angle.
Fig.51: 1. Guide fence 2. Crown molding stopper
26 ENGLISH
Molding
edge against
guide fence
(a) Wall contact Finished
edge should piece will be
be against on the Right
guide fence. side of blade.
(b) Ceiling
contact edge
(c) Finished
should be
piece will be
against guide
on the Left
fence.
side of blade.
(d) Wall contact
edge should
be against
guide fence.
Finished
piece