BFT SUB Instrucciones De Uso Y De Instalacion página 5

Thank you for buying this product, our company is sure that you will be more
than satisfied with its performance. This product is supplied with a
"WARNINGS" leaflet and an "INSTRUCTION MANUAL". These should
both be read carefully as they provide important information about safety,
installation, operation and maintenance. This product complies with
recognised technical standards and safety regulations. We declare that this
product is in conformity with the following European Directives: 73/23/EEC,
98/37 EEC and subsequent amendments.
1) GENERAL OUTLINE
The SUB hydraulic controller provides the ideal solution for underground
hinge-pivot installations, as it brilliantly solves aesthetic automation
problems. The SUB actuator consists of a perfectly sealed single block,
containing a hydraulic control unit and a jack, which provides a hidden
underground installation without any hydraulic connections. The gate is
kept closed by an electric lock, or by a hydraulic lock on the SUB versions
supplied with it. The versions with slow-down functions avoid unpleasant
slamming noise when the gate is brought to the final opening and closing
stages. The pushing force can be adjusted with extreme precision by
means of two by-pass valves which provide antisquash safety. The end-of-
stroke operation is electronically set by a timer on the control panel. The
emergency release, activated by the proper key supplied, can be easily
reached after removing the appropriate cap found on the cover.
2) MAIN AUTOMATION PARTS
Single-block hydraulic actuator (fig.1) consisting of:
M) 2-pole single-phase motor protected by thermal circuit-breaker.
P) Hydraulic lobe pump.
D) Distributor with adjustment valves.
PC) Rack - pinion jack.
Components supplied as standard: by-pass release and adjustment key,
capacitor, grooved bush and instruction manual.
WARNING: An actuator can be mounted on the left or right-hand side, as
identified by looking at the gate from the inside (opening direction). An
actuator can be recognised as left or right-handed by observing the position
of release pivot "PST". Fig.1 shows an actuator to be mounted on the left.
3) ACCESSORIES
- CPS Bearing foundation case (provided for automation).
- CID Non-bearing foundation case.
- BSC Slide arm (for mounting to one side of the hinge-pivot).
4) MANUAL OPENING
In case of emergency, for instance when there is no power available, the
gate must be opened by hand.
OPEN
CLOSE
USER'S MANUAL
5) AUTOMATION OPERATION
As automation can be remotely controlled by means of a radio control or
start button, it is essential to frequently check that all safety devices are
perfectly efficient. In case of any operational malfunction, take immediate
action and request the assistance of qualified personnel. It is recommended
to keep children at a safe distance from the automation field of action.
6) MAINTENANCE
ATTENTION: The oil of each actuator must be replaced completely every
two years. Only use oil of the same type (IDROLUX).
7) SCRAPPING
Materials must be disposed of in conformity with the current regulations. In
case of scrapping, the automation components do not entail any particular
risks or danger. In case of recovered materials, these should be sorted out
by type (electrical components, copper, aluminium, plastic etc.).
8) DISMANTLING
When the automation system is disassembled to be reassembled on
another site, proceed as follows:
-
-
-
-
9) MALFUNCTION: CAUSES and REMEDIES
When any operational malfunction is found, and not resolved, disconnect
the power supply from the system and request the assistance of qualified
personnel (installer). When automation is out of order, activate the manual
release to allow opening and closing manoeuvres to be carried out by hand.
Fig. 1
C
PST
D P
Disconnect the power supply and the entire electrical installation.
Remove the gearmotor from its fixing base.
Disassemble the control panel, if separate, and all the installation
components.
In the case where some of the components cannot be removed or are
damaged, they must be replaced.
PC
M
P:5
ENGLISH
5
SUB - Ver. 03 -