Optional Accessories - Makita LH1201FL Manual De Instrucciones

Ocultar thumbs Ver también para LH1201FL:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 63
Make sure that the pointer on the turn base point to
0° on the bevel scale on the arm. If it does not point
to 0°, loosen the screw which secures the pointer
and adjust the pointer so that it will point to 0°.
(Fig. 53)
(2) 45° bevel angle
Adjust the 45° bevel angle only after performing 0°
bevel angle adjustment. To adjust left 45° bevel
angle, loosen the lever and tilt the blade to the left
fully. Make sure that the pointer on the arm points to
45° on the bevel scale on the arm. If the pointer
does not point to 45°, turn the 45° bevel angle
adjusting bolt on the left side of the arm until the
pointer points to 45°. (Fig. 54)
Replacing carbon brushes (Fig. 55 & 56)
Remove and check the carbon brushes regularly.
Replace when they wear down to 3 mm in length. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
After use
• After use, wipe off chips and dust adhering to the tool
with a cloth or the like. Keep the blade guards clean
according to the directions in the previously covered
section titled "Blade guard". Lubricate the sliding por-
tions with machine oil to prevent rust.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Steel & Carbide-tipped saw blades
• Vise assembly (Horizontal vise)
• Vertical vise
• Socket wrench 13
• Holder set
• Dust bag
• Triangular rule
• Blade cover
• Push stick
• Ruler assembly (Rip fence)
NOTE:
• Some items in the list may be included in the tool pack-
age as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to EN61029:
Model LH1201FL 220 V – 240 V
Sound pressure level (
Sound power level (
Uncertainty (K): 3 dB (A)
Model LH1201FL 110 V
Sound pressure level (
Sound power level (
Uncertainty (K): 3 dB (A)
Wear ear protection
For European countries only
EC Declaration of Conformity
Makita declares that the following Machine(s):
Designation of Machine:
Table Top Miter Saw
Model No./ Type: LH1201FL
Conforms to the following European Directives:
2006/42/EC
They are manufactured in accordance with the following
standard or standardized documents:
EN61029
The technical file in accordance with 2006/42/EC is
available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
31.7.2015
Yasushi Fukaya
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
): 93 dB (A)
L
pA
): 106 dB (A)
L
WA
): 95 dB (A)
L
pA
): 108 dB (A)
L
WA
Director
ENG905-1
ENH003-15
21
Tabla de contenido
loading

Tabla de contenido