Display Mode - Cardin Elettronica GL Serie Manual Del Usuario

DISPLAY MODE

Using the PROG button you can access the following functions
in sequence:
- memorising the status of the dip-switches;
- display the status of the command and safety devices;
- display the number of manoeuvres;
The status of the security devices TB, FTCI, CSP,
CSPF are always shown on the display.
Memorising the DIP-SWITCH settings and displaying
the firmware version (e.g. "10")
The segments regarding the command status (LED
"ON" = command active) and safety status (LED "ON"
= safety device at rest) light up.
The number of manoeuvres appears on the display.
This number always remains visible until you change
the setting. Once 999999 has been exceeded the
lighting up of the decimal point on the display equals 1
million + the six figure number.
In the "test" mode (only activated when the motor has
stopped) it is possible to check the status of the
command and safety devices. The warning lights will
activate once, each time a ("TD-TB-FTCI-CSP-CSPF")
command is received. In this mode you can activate
serial line communication by using the external
program, which is to be connected to the CSER
connection via cable (fig. 31). While communication is
active dashes will appear on the display; after 5
seconds of inactivity you will be moved back to the
"test" mode. To return to the normal operating mode
press the button again "test" will appear, then wait for
10 seconds.
drA = Setting the reclosing function with an obstacle:
PRESS
- "1" = the programmer tries to close three times.
PROG
- "0" = the programmer tries to close once.
SNS = Setting the current sensor.
PRESS
1 = motor consumption + 1 amp
PROG
2 = motor consumption + 2 amps
3 = motor consumption + 3 amps
10 sec
dSt = Setting the distance from the opening
PRESS
direction travel limit (approximate values):
PROG
- "0" = 0 centimetres - "1" = 1 centimetre
- "2" = 2 centimetres - "3" = 3 centimetres
10 sec
SC = Safety contact selection (N.C./8.2 kOhm)
PRESS
0 = CSP, TB, FTCI: contact N.C.
PROG
1 = CSP: 8.2 kOhm / TB, FTCI: contact N.C.
2...7 see "Safety contact selection" on page 28
10 sec
CSPF = Enable digital safety edge
PRESS
0 = Digital safety edge disabled
PROG
1 = Digital safety edge enabled
PRESS PROG
PRESS PROG
PRESS PROG
PRESS PROG
10 sec
10 sec
- access the "test" mode;
- enabling/disabling automatic reclosing in the presence of an obstacle;
- setting the current sensor level;
- setting the distance from the opening direction travel limit;
- safety contact selection (N.C./8.2 kΩ);
- enabling the digital safety edge.
10 sec
10 sec
When the ("TD-TB-FTCI,CSP,CSPF") inputs are
activated the warning and courtesy lights will light up.
5 sec
Connect the
programming device
(CSER) and activate it.
10 sec
PRESS PROG
Each time "PROG" is pressed the
selection switches between "1" and "0".
10 sec
PRESS PROG
Each time "PROG" is pressed the
selection switches from "1" to "3".
10 sec
PRESS PROG
Each time "PROG" is pressed the
selection switches from "0" to "3".
10 sec
PRESS PROG
Each time "PROG" is pressed the
selection switches from "0" to "7".
10 sec
PRESS PROG
Each time "PROG" is pressed the
selection switches between "0" and "1".
25
PRESS PROG
10 sec
10 s after the last modification the
mode will quit automatically and the
10 sec
selected values will be saved (e.g. 0)
10 s after the last modification the
mode will quit automatically and the
10 sec
selected values will be saved (e.g. 3)
10 s after the last modification the
mode will quit automatically and the
10 sec
selected values will be saved (e.g. 1)
10 s after the last modification the
mode will quit automatically and the
10 sec
selected values will be saved (e.g. 1)
10 s after the last modification the
mode will quit automatically and the
10 sec
selected values will be saved (e.g. 1)