BFT DEIMOS Instrucciones De Uso Y De Instalacion página 15

(in the open), it has to be at least equal to H07RN-F, but if it is on the
inside (or outside but placed in a plastic cable cannel) it has to be or
at least egual to H05VV-F with section 3x1.5mm
JP1
1-2 Power supply 230V +/- 10% 50/60 Hz (Neutral to terminal 1).
3-4-5 Connection to motor M (terminal 4 common, terminals 3-5 motor and
capacitor drive).
1-4 Connection to blinker and electric lock 230V mod. EBP.
JP2
7-8 START pushbutton or key selector (N.O.).
7-9 STOP pushbutton (N.C.). If not used, leave the bridge connected.
7-10 Photocell input or pneumatic edge (N.C.). If not used, leave the bridge
connected.
7-11 Opening limit switch (N.C.). If not used, leave the bridge connected.
7-12 Closing limit switch (N.C.). If not used, leave the bridge connected.
13-14 Output 24Va.c. supply to photocells or other devices.
15-16 Output for gate-open warning light outputor alternatively 2nd radio
channel.
17-18 Antenna input for radio-receiver plug-in board (20 braid–19 signal).
JP3
19-20 Pedestrian input (N.O.)
JP4 Radio-receiver board connector, 1-2 channels.
Fig.20 shows a general wiring diagram.
5) LED (Fig.21)
The ALPHA control unit is provided with a series of self-diagnosis leds
which control all the functions.
DL1: Incorporated radio receiver LED
DL2: START - Start - goes on when a start command is given.
DL3: STOP - Stop - goes off when a start command is given.
DL4: PHOT - Photocell - goes off when the photocells are not aligned or in
the presence of obstacles.
DL5: SWO - Goes off when the opening limit switch is operated.
DL6: SWC - Goes off when the closing limit switch is operated.
6) DIP-SWITCH SELECTION (Fig.21)
DIP1)
TCA [ON] - Automatic closing time TCA.
ON Activates automatic closing
OFF Excludes automatic closing
DIP2)
FCH [ON] - Photocells.
ON: Photocells are only active in the closing phase.
OFF: Photocells are active both in the closing and opening phase.
DIP3)
BLI - Blocks impulses.
ON: START commands are not accepted during the opening phase.
OFF: START commands are accepted during the opening phase.
DIP4)
3P/4P - 3 Steps/4 Steps
ON: Enables 3-step logic.
OFF: Enables 4-step logic.
DIP5)
CODE FIX – Fixed code.
ON: Activates incorporated receiver in fixed code mode.
OFF: Activates incorporated receiver in rolling-code mode.
DIP6)
RADIO LEARN - Radio transmitter programming
ON: This enables transmitter storage via radio:
1 – First press the hidden key (P1) and then the normal key (T1, T2,
T3 or T4) of a transmitter already memorised in standard mode by
means of the radio menu.
2 – Within 10s press the hidden key (P1) and the normal key (T1, T2,
T3 or T4) of a transmitter to be memorised.
The receiver exits the programming mode after 10s, other new
transmitters can be entered before the end of this time.
This mode does not require access to the control panel.
OFF This disables transmitter storage via radio. The transmitters can only
be memorised using the appropriate Radio menu.
DIP7)
SCA – Gate-open warning light or 2nd radio channel.(Fig. 24).
INSTALLATION MANUAL
ON:
OFF: Activates relay output as 2nd radio channel.
2 .
DIP8)
FAST CLOSE
ON
OFF Command not entered.
7) TRIMMER ADJUSTMENT (Fig.21)
TCA (Dip1 ON).
It is used to set the automatic closing time, after which the gate closes
automatically (adjustable from 0 to 90 sec.).
TW
It is used to set the motor working time, after which the motor stop (adjustable
from 0 to 90 sec.). When using electrical limit switches, increase the motor
stopping time by a few seconds with respect to the leaf closing time.
8) INTEGRATED RECEIVER TECHNICAL SPECIFICATION
Receiver output channels:
- output channel 1, if activated, controls a START command.
- output channel 2, if activated, controls the excitation of the 2nd radio
channel relay for 1s.
Transmitter versions which can be used:
all Rolling Code transmitters compatible with
ANTENNA INSTALLATION
Use an antenna tuned to 433MHz.
For Antenna-Receiver connection, use RG8 coaxial cable.
The presence of metallic masses next to the antenna can interfere with
radio reception. In case of insufficient transmitter range, move the antenna
to a more suitable position.
9) PROGRAMMING
Transmitter storage can be carried out in manual mode, or by means of the
UNIRADIO programmer which allows you to create installations in the
"collective receivers" mode, as well as manage the complete installation
database using the EEdbase software.
10) MANUAL PROGRAMMING
In the case of standard installations where no advanced functions are
required, it is possible to proceed to manual storage of the transmitters
1) If you wish the transmitter T key to be memorised as Start , press the SW1
button on the control unit, otherwise if you wish the transmitter key to be
memorise as second radio channel, press the SW2 button on the control
unit.
2) When the DL1 LED blinks, press the transmitter P1 hidden key, and the DL1
LED will stay on permanently.
3) Press the key to be memorised on the transmitter, LED DL1 will start
blinking again.
4) To memorise another transmitter, repeat steps 2) and 3).
5) To exit the storage mode, wait until the LED is switched off completely.
IMPORTANT NOTE: ATTACH THE ADHESIVE KEY LABEL TO THE
FIRST MEMORISED TRANSMITTER (MASTER).
In the case of manual programming, the first transmitter assigns the key
code to the receiver; this code is necessary in order to carry out subsequent
cloning of the radio transmitters.
10.1) CONTROL UNIT MEMORY CANCELLATION
In order to cancel the control unit memory completely, simultaneously press for
10 seconds the SW1 and SW2 buttons on the control unit (DL1 LED blinking).
Correct memory cancellation will be indicated by the DL1 LED staying on
permanently. To exit the storage mode, wait until the LED is switched off
completely.
11) RECEIVER CONFIGURATION
The on-board receiver combines characteristics of utmost safety in copying
variable code (rolling code) coding with the convenience of carrying out
transmitter "cloning" operations thanks to an exclusive system.
Cloning a transmitter means creating a transmitter which can be automatically
included within the list of the transmitters memorised in the receiver, either
as an addition or as a replacement of a particular transmitter.
Cloning by replacement is used to create a new transmitter which takes the
place of the one previously memorised in the receiver; in this way a specific
transmitter can be removed from the memory and will no longer be usable.
Therefore it will be possible to remotely program a large number of
Activates relay output in Gate-open warning light mode.
Closes the gate after photocell disengagement, before waiting for the
end of the TCA set.
ENGLISH
DEIMOS - DEIMOS 700 Ver. 01 -
15