Bosch EasySpray 18V-100 Manual Original página 21

Ocultar thumbs Ver también para EasySpray 18V-100:
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 38
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Inserting the Battery
Push the charged battery into the battery holder until it
clicks into place.
Removing the Battery
To remove the rechargeable battery, press the battery re-
lease button and pull the battery out. Do not use force to do
this.
Battery charge indicator
The battery charge indicator indicates the remaining battery
capacity or an overload for a few seconds when the power
tool is switched on.
LED
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × flashing green light
3 × flashing green light
The three LEDs in the battery charge indicator flash quickly
when the temperature of the rechargeable battery is outside
the operating temperature range and/or the overload protec-
tion has been triggered.
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Ensure that the spray gun and base unit are as-
u
sembled completely and with all seals. Only this will en-
sure the function and safety of the fine-spray system.
Ensure that a nozzle cap that was delivered with the
u
spray gun is fitted. Only this will ensure the function and
safety of the fine-spray system.
Bosch Power Tools
Connecting the air hose (see figures A1–A2)
Connecting the base unit:
– Insert a bayonet lock (18) of the air hose securely into the
holes in the base unit port (25) according to the arrow
marks.
– Turn the bayonet lock a quarter turn clockwise.
Connecting to the spray gun:
– Insert the second bayonet lock (18) of the air hose se-
curely into the holes in the spray gun port (4) according
to the arrow marks.
– Turn the bayonet lock a quarter turn clockwise.
Note: Remove the air hose (17) before pouring in spray ma-
terial (quarter turn of the bayonet lock (18) anticlockwise;
pull the bayonet lock (18) out of the port (4)).
Attaching the carrying strap (see figure B)
To be able to reach all surfaces to be sprayed and to main-
Capacity
tain flexibility, you can carry the base unit by means of the
67–100 %
strap (26).
34–66 %
– Attach one strap end to each eyelet (27).
11–33%
Operation
1–10 %
0 %
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Work preparation
Spraying on the sides of water bodies (lakes, rivers,
u
etc.) or neighbouring surfaces in the direct catchment
area is not permitted.
When purchasing paint, lacquer and spray material, pay
u
attention to their environmental compatibility.
Preparing the spray surface
The spray surface must be clean, dry and grease-free.
– Roughen smooth surfaces and then remove the sanding
dust.
When spraying, all non-covered surfaces can be contamin-
ated by the spray mist. Therefore, thoroughly prepare the
area around the surface to be sprayed:
– Carefully cover floors, furnishings, doors, windows as
well as door and window frames, etc. Painting substrate,
for example, is recommended for covering the floors.
– Fix the cover material in place. Cover material that is not
fixed in place securely can be detached or blown away by
the powerful air jet.
Carefully mask off plug sockets and switches. Un-
u
covered plug sockets and switches may cause a short-cir-
cuit and increase the risk of electric shock.
English | 21
1 609 92A 848 | (11.07.2022)
loading

Este manual también es adecuado para:

0 603 208 000