Idiomas disponibles
Idiomas disponibles
22 | English
Preparing the spray material
When diluting, make sure that the spray material and
u
the diluting agent are compatible. When using a faulty
diluting agent, lumps can develop that can lead to clog-
ging of the spray gun.
When diluting the spray material, make sure that the
u
flash point of the mixture is above 55 °C again after di-
luting. Diluting substances such as solvent-based lac-
quers lowers the flash point.
Note the specifications of the paint manufacturer re-
u
lating to sprayability, e.g. in the technical information
sheet or data sheet. Make sure that you do not spray
any paints that are not suitable according to the man-
ufacturer's specifications.
– Stir the spray material thoroughly.
Using spray material at room temperature will yield a bet-
ter spray pattern.
– Dilute the spray material if necessary.
If the spray test does not produce a good spray pattern,
dilute in 5 % increments until an optimal spray pattern is
achieved.
Spray material
Wood preservatives, water, oils,
thin varnishes
Impregnations, anti-rust primers
Solvent-dilutable or water-dilutable
(recommended) lacquers, primers,
radiator lacquers, thick varnishes
Dilution table
Spray mater-
Diluting agent [ml] for dilution
ial
5 %
[ml]
300
15
400
20
500
25
600
30
Filling the spray material (see figures C1–C2)
Note: Remove the air hose (17) before pouring in spray ma-
terial (quarter turn of the bayonet lock (18) anticlockwise;
pull the bayonet lock (18) out of the port (4)).
For spray jobs on horizontal
Towards the front in the dir-
surfaces/objects
ection of the nozzle/air cap
For spray jobs overhead
Towards the rear in the dir-
ection of the handle
1 609 92A 848 | (11.07.2022)
– When using large buckets, pour the spray material into a
– Unscrew the container (7) from the spray gun.
– Pour the spray material into the container (7) up to no
– Turn the suction tube (12) so that the spray material can
– Carry out a test-spray run on a test surface.
If the spray pattern is optimal, you can begin spraying.
or
If the spraying results are unsatisfactory or no paint is emit-
ted: (see "Troubleshooting", page 25)
Starting Operation
u
u
u
u
u
Recommended dilu-
Switching on (see figure D)
tion
– Insert the rechargeable battery.
0 %
– Grasp the spray gun by the handle and point it at the tar-
0−5 %
– Slide the on/off switch (20) forwards.
At least 5 %
– Pull the trigger switch (6) on the spray gun.
Note: Air always flows out at the air cap (2) when the base
unit is switched on.
Switching Off
– Let go of the trigger switch (6) and slide the on/off
10 %
15 %
– Remove the rechargeable battery.
30
45
40
60
Working Advice
50
75
Spraying (see figure E)
60
90
Note: Pay attention to the wind direction when you are using
the power tool outdoors.
– Firstly, carry out a spray test and adjust the spray pattern
– Make sure to hold the spray gun with a uniform clearance
– Begin the spraying procedure outside the target area.
smaller transfer bucket if necessary (e.g. 10 l wall paint
into an empty 2.5 or 5.0 l bucket).
more than the 800 mark.
be sprayed with almost no residue:
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Make sure that the base unit cannot draw in dust or
other contamination during operation.
Make sure never to spray on the base unit.
Stop spraying if fluid escapes from places other than
the intended nozzle during spraying, and restore the
spray gun to its proper condition. There is a risk of elec-
tric shock.
Do not direct the fine-spray system against yourself,
other persons or animals.
get area.
switch (20) backwards.
and the spray material quantity according to the spray
material.
For adjustments, see the following sections.
of 15–20 cm vertical to the object being sprayed.
Bosch Power Tools
