Idiomas disponibles
Idiomas disponibles
5. To remove the guard, open the guard latch, rotate the
guard so that the arrows are aligned and pull up on
the guard.
NoTE: If, after a period of time the closed (Type 1) guard
becomes loose, tighten the adjusting screw with the clamp
lever in the closed position.
CAUTION: If the guard cannot be tightened by the
adjusting screw, do not use the tool. To reduce the
risk of personal injury, take the tool and guard to an
authorized repair agent to repair or replace the guard.
NOTICE: Do not tighten adjusting screw with clamp
lever in open position. Undetectable damage to guard
or mounting hub may result.
Flanges and Wheels
Mounting Non‑Hubbed Wheels (Fig. D, E1, E2)
WARNING: Failure to properly seat the flange/ clamp
nut/ wheel could result in serious injury (or damage to
the tool or wheel).
CAUTION: Included flanges must be used with
depressed centre Type 27 and Type 42 grinding wheels
and Type 41 cutting wheels. See the Grinding and
Cutting accessory Chart for more information.
WARNING: A closed, two-sided cutting wheel guard is
re quired when using cutting wheels.
WARNING: Use of a damaged flange or guard or
fail ure to use proper flange and guard can re sult in
injury due to wheel breakage and wheel contact. See
the Grinding and Cutting accessory Chart for
more information.
1. Place the tool on a table, guard up.
2. Install the backing flange
centre (pilot) facing the wheel. Press the backing flange
into place.
3. Place the wheel
11
on the backing flange
fitting a wheel with a raised centre, make sure that the
raised centre
12
is facing the backing flange
4. Screw the locking flange
a. The ring on the locking flange
the wheel when fitting a grinding wheel (Fig. E1);
b. The ring on the locking flange
the wheel when fitting a cutting wheel (Fig. E2).
5. Press the spindle lock button
until it locks in position.
6. Tighten the locking flange
7. Release the spindle lock.
8. To remove the wheel, reverse the above procedure.
Mounting Sanding Backing Pads (Fig. A, F)
NoTE: Use of a guard with sanding discs that use backing
pads, often called fiber resin discs, is not required. Since a
guard is not required for these accessories, the guard may or
may not fit correctly if used.
WARNING: Failure to properly seat the flange/ clamp
nut/ wheel could result in serious injury (or damage to
the tool or wheel).
4
on spindle
2
with the raised
4
. When
4
.
5
onto the spindle
2
:
5
must face toward
5
must face away from
1
and rotate the spindle
5
with the wrench supplied.
WARNING: Proper guard must be reinstalled for
grinding wheel, cutting wheel, sanding flap disc,
wire brush or wire wheel applications after sanding
applications are complete.
1. Remove the backing flange
2. Place or appropriately thread backing pad
the spindle.
3. Place the sanding disc
4. While depressing spindle lock button
nut
15
on spindle, piloting the raised hub on the clamp
nut into the centre of san ding disc and backing pad.
5. Tighten the clamp nut by hand. Then depress the spindle
lock button while turning the sanding disc until the
sanding disc and clamp nut are snug.
6. To remove the wheel, grasp and turn the backing
pad and sanding pad while depressing the spindle
lock button.
Mounting and Removing Hubbed Wheels
(Fig. A)
Hubbed wheels install directly on the threaded spindle.
Thread of accessory must match thread of spindle.
1. Remove backing flange by pulling away from tool.
2. Thread the wheel on the spindle
3. Depress the spindle lock button
tighten the hub of the wheel.
4. Reverse the above procedure to remove the wheel.
NOTICE: Failure to properly seat the wheel before
turning the tool on may result in damage to the tool
or the wheel.
Mounting Wire Cup Brushes and Wire Wheels
(Fig. A)
WARNING: Failure to properly seat the flange/ clamp
nut/ wheel could result in serious injury (or damage to
the tool or wheel).
CAUTION: To reduce the risk of personal injury,
wear work gloves when handling wire brushes
and wheels. They can become sharp.
CAUTION: To reduce the risk of damage to the
tool, wheel or brush must not touch guard when
mounted or while in use. Undetectable damage
could occur to the accessory, causing wires to fragment
2
from accessory wheel or cup.
Wire cup brushes or wire wheels install directly on the
threaded spindle without the use of flanges. Use only wire
brushes or wheels provided with a threaded hub. These
accessories are available at extra cost from your local dealer
or authorised service centre.
1. Place the tool on a table, guard up.
2. Thread the wheel on the spindle by hand.
3. Depress spindle lock button
hub of the wire wheel or brush to tighten the wheel.
4. To remove the wheel, reverse the above procedure.
NOTICE: To reduce the risk of damage to the tool,
properly seat the wheel hub before turning the tool on.
by pulling away from tool.
4
13
on
on the backing pad.
14
1
, thread clamp
by hand.
2
1
and use a wrench to
1
and use a wrench on the
ENGlish
35
