Idiomas disponibles
Idiomas disponibles
Getting
To Know
Your
Miter
Saw
To avoid injury from accidental start-
ing, remove plug from power source
outlet before making any adjustments.
1. Switch Lock-Off
Release Button - One of these
two buttons must be pressed before the power
switch can be pressed.
2. Power Switch
- The power switch used with the
"Lock-OFF" button energizes the unit.
3. Main Handle - This handle contains the power
switch. Pulling this handle down lowers the blade
into the workpiece.
4. Brush Caps - These caps keep the motor brush-
es in position and provide easy access for inspect-
ing and replacing brushes.
5. Lower
Blade
Guard/Lower
Guard
Lip - The
lower blade guard helps protect your hands from
the spinning blade. It retracts as the blade is low-
ered. Lip can be used to raise the lower guard
when guard becomes jammed on a workpiece.
6. Blade - Use only 10" blades with 5/8" arbor hole.
7. Sliding
Fence - Supports
the workpiece.
The
fence has a cast in scale to make repetitive cuts
easy. The fence also has holes to secure an auxil-
iary fence if desired.
8. Kerf Inserts - Kerf inserts can be adjusted to dif-
ferent blade widths to minimize workpiece tear-out.
9.
Miter Detent Override
- Allows detent action to
be locked out allowing for micro adjustments
to
any miter angle.
10. Miter Scale/Miter
Angle Indicator
- This scale is
cast in on the base of the saw. Indicator is fas-
tened to the table.
11. Miter Detents - There are ten (10) miter detent
slots for fast and accurate miter cuts of common
miter angles.
12. Miter Detent
Lever
- The lever releases the
table from the detent.
13. Miter Lock Knob - The miter lock knob locks the
miter saw table at any desired miter angle.
14. Table - Sits in base, provides workpiece support,
rotates for desired
miter cuts and rotates the
head assembly. The front extended part of the
table is called the miter arm.
15. Base -
Provides
working
surface
to support
workpiece.
16. Tool Mounting
Pads - The four corners of the
saw provide areas to clamp, bolt or nail the saw
to a flat work surface.
17. Sliding
Base
Extensions-
These extensions
provide extra workpiece
support and are espe-
cially useful when cutting long workpieces.
18. Base Extension
Clamping
Levers - Locks the
base extensions at desired positions.
19. Length
Stop - For repetitive cuts of the same
length. Can be moved to left side, if desired.
20. Dust Port - The dust port can accommodate
the
dust chute and dust bag or optional
VAC004
Vacuum
Hose Adapter,
which accepts
Bosch
35mm hoses.
21. Bevel Lock Lever - The front-positioned
bevel
lock lever locks the head assembly at the desired
bevel angle.
22. Bevel Range Selector
Knob - Allows selection
of the bevel range, 0 ° to 45 ° left, 0 ° to 45 ° right,
and complete range of 47 ° left to 46 ° right.
23. Microfine Miter Adjustment
System - Allows
for fine adjustment (up to 2 degrees to the left or
right) of the detent angles.
24. Slide Rail Lock Knob - Locks the slide rails
when not making slide cuts or when transporting
the saw.
25. Slide Rails - Guide the head assembly when
making slide cuts.
26. Quick-Action
Clamp
Position
Holes-
There
are two (2) holes (not shown) behind the fence for
placing the quick action clamp.
27. Lower
Guard
Actuation
Link
- Allows
for
smooth movement of the lower guard.
28. Upper Blade Guard - Covers upper portion of
the blade.
29. Cord Wrap - Allows you to easily wrap up the
cord so it's out of the way when transporting or
storing.
30. Power Cord - Supplies power to motor.
31. Rear
Cover
Tool
Storage
-
Storage
for
10mm/17mm
Combination
Open End Wrench
and 1.5mm & 3mm Hex "L" Wrenches.
32. Bevel Detent Pin (Crown
Molding Setting)
-
Allows you to easily lock the head assembly to
the bevel angle of 33.9 ° to the left or right.
33. Bevel Scale - This scale is large and angled to
allow you to easily read bevel angles.
34. Head Assembly
Lock Pin - Used to lock the
head assembly in the lower position for transport-
ing.
35. Quick Release Depth Stop Button - Allows you
to quickly release the depth stop.
36. Depth Stop Fine Adjustment
Knob-Allows
you
to adjust
the depth
of the blade for cutting
grooves in the workpiece.
37. Handle
Rotation
Release
Lever - Pulling this
lever allows the handle to be rotated. Release the
lever into one of four operating positions.
38. Rear Carrying
Handle - Used for lifting of the
tool.
39. Handle
Clamp - Locks handle in the selected
position.
40. Arbor Lock--Keeps
the blade from rotating while
tightening or loosening arbor screw during blade
replacement or removal.
41. Front Carrying
Handle - Used for lifting the tool.
42. Dust Bag and Dust Elbow - Used to collect saw
dust.
43. Sliding
Fence Lock Knob - Used to hold fence
position after slide adjustment.
44. Arbor Laser / 3x Battery.
.
